Carte TV Terratec Cinergy HT PCMCIA sous linux

Bonjour,

Je viens de faire l'acquisition d'une terratec Cinergy HT PCMCIA pour
mon portable et je n'arrive pas du tout =C3=A0 la faire fonctionner, que se
soit pour la t=C3=A9l=C3=A9 num=C3=A9rique ou analogique.

Apparemment, =C3=A0 l'insertion, la carte a l'air correctement reconnue
(noyau 2.6.22-14-generic ):
Dec 5 21:39:36 port-erwan kernel: [ 121.212000] pccard: CardBus card inse=
rted into slot 1=20
Dec 5 21:39:36 port-erwan kernel: [ 121.324000] Linux video capture inter=
face: v2.00=20
Dec 5 21:39:37 port-erwan kernel: [ 121.396000] saa7130/34: v4l2 driver v=
ersion 0.2.14 loaded=20
Dec 5 21:39:37 port-erwan kernel: [ 121.396000] PCI: Enabling device 0000=
:05:00.0 (0000 -> 0002)=20
Dec 5 21:39:37 port-erwan kernel: [ 121.396000] ACPI: PCI Interrupt 0000:=
05:00.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11=20
Dec 5 21:39:37 port-erwan kernel: [ 121.396000] saa7133[0]: found at 0000=
:05:00.0, rev: 209, irq: 11, latency: 0, mmio: 0x40000000=20
Dec 5 21:39:37 port-erwan kernel: [ 121.396000] PCI: Setting latency time=
r of device 0000:05:00.0 to 64 Dec 5 21:39:37 port-erwan kernel:
[ 121.396000] saa7133[0]: subsystem: 153b:1172, board: Terratec Cinergy HT=
PCMCIA [card=3D105,autodetected]=20
Dec 5 21:39:37 port-erwan kernel: [ 121.396000] saa7133[0]: board init: g=
pio is 0=20
Dec 5 21:39:37 port-erwan kernel: [ 121.536000] saa7133[0]: i2c eeprom 00=
: 3b 15 72 11 54 20 1c 00 43 43 a9 1c 55 d2 b2 92=20
Dec 5 21:39:37 port-erwan kernel: [ 121.536000] saa7133[0]: i2c eeprom 10=
: 00 ff 86 0f ff 20 ff 00 01 50 32 79 01 3c ca 50=20
Dec 5 21:39:37 port-erwan kernel: [ 121.536000] saa7133[0]: i2c eeprom 20=
: 01 40 01 02 02 03 01 00 06 ff 00 1b 02 51 96 2b=20
Dec 5 21:39:37 port-erwan kernel: [ 121.536000] saa7133[0]: i2c eeprom 30=
: a7 58 7a 1f 03 8e 84 5e da 7a 04 b3 05 87 b2 3c Dec 5 21:39:37 port-erwa=
n kernel: [ 121.536000] saa7133[0]: i2c eeprom 40: ff 21 00 c2 96 10 03 22=
15 10 fd 79 44 9f c2 8f=20
Dec 5 21:39:37 port-erwan kernel: [ 121.536000] saa7133[0]: i2c eeprom 50=
: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff=20
Dec 5 21:39:37 port-erwan kernel: [ 121.536000] saa7133[0]: i2c eeprom 60=
: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff=20
Dec 5 21:39:37 port-erwan kernel: [ 121.536000] saa7133[0]: i2c eeprom 70=
: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff Dec 5 21:39:37 port-erwa=
n kernel: [ 121.636000] tuner 3-004b: chip found @ 0x96 (saa7133[0]) =20
Dec 5 21:39:37 port-erwan kernel: [ 121.684000] tuner 3-004b: setting tun=
er address to 61=20
Dec 5 21:39:37 port-erwan kernel: [ 121.724000] tuner 3-004b: type set to=
tda8290+75a=20
Dec 5 21:39:38 port-erwan kernel: [ 123.144000] tuner 3-004b: setting tun=
er address to 61=20
Dec 5 21:39:38 port-erwan kernel: [ 123.184000] tuner 3-004b: type set to=
tda8290+75a=20
Dec 5 21:39:40 port-erwan kernel: [ 124.544000] saa7133[0]: registered de=
vice video0 [v4l2]=20
Dec 5 21:39:40 port-erwan kernel: [ 124.544000] saa7133[0]: registered de=
vice vbi0=20
Dec 5 21:39:40 port-erwan kernel: [ 124.676000] saa7134 ALSA driver for D=
MA sound loaded=20
Dec 5 21:39:40 port-erwan kernel: [ 124.676000] saa7133[0]/alsa: saa7133[=
0] at 0x40000000 irq 11 registered as card -2 Dec 5 21:39:40 port-erwan ke=
rnel: [ 125.240000] DVB: registering new adapter (saa7133[0]).=20
Dec 5 21:39:40 port-erwan kernel: [ 125.240000] DVB: registering frontend=
0 (Philips TDA10046H DVB-T)...=20
Dec 5 21:39:40 port-erwan kernel: [ 125.316000] tda1004x: setting up plls=
for 48MHz sampling clock=20
Dec 5 21:39:42 port-erwan kernel: [ 127.312000] tda1004x: found firmware =
revision 26 -- ok=20
Dec 5 21:40:27 port-erwan kernel: [ 171.820000] tda1004x: setting up plls=
for 48MHz sampling clock=20
Dec 5 21:40:29 port-erwan kernel: [ 173.768000] tda1004x: found firmware =
revision 26 -- ok=20
Dec 5 21:40:40 port-erwan kernel: [ 184.756000] tda1004x: setting up plls=
for 48MHz sampling clock=20
Dec 5 21:40:42 port-erwan kernel: [ 186.700000] tda1004x: found firmware =
revision 26 -- ok=20
Dec 5 21:46:18 port-erwan kernel: [ 522.692000] tda1004x: setting up plls=
for 48MHz sampling clock=20
Dec 5 21:46:20 port-erwan kernel: [ 524.640000] tda1004x: found firmware =
revision 26 -- ok=20
Dec 5 21:50:11 port-erwan kernel: [ 755.800000] tda1004x: setting up plls=
for 48MHz sampling clock=20
Dec 5 21:50:13 port-erwan kernel: [ 757.748000] tda1004x: found firmware =
revision 26 -- ok=20
Dec 5 21:50:25 port-erwan kernel: [ 770.004000] tda1004x: setting up pll=
s for 48MHz sampling clock
Dec 5 21:50:27 port-erwan kernel: [ 771.952000] tda1004x: found firmware =
revision 26 -- ok


en v=C3=A9rifiant dans /dev, =C3=A7a a l'air correct :
/dev/video0 existe et le dossier /dev/dvb/adapter0
#ls /dev/dvb/adapter0/*
/dev/dvb/adapter0/demux0 /dev/dvb/adapter0/dvr0 /dev/dvb/adapdvbsnoopter0=
/frontend0 /dev/dvb/adapter0/net0

petite pr=C3=A9cision, pas de webcam au moment o=C3=B9 ces tests sont faits=
, la carte PCMCIA est cens=C3=A9e =C3=AAtre mon seul p=C3=A9riph=C3=A9rique=
v4l.

les paquets dvb sont biens install=C3=A9s =C3=A0 savoir :
dvb-utils
dvbsnoop
dvbstream
dvbtune
libdvbpsi3
libdvbpsi4

Et malgr=C3=A9 cela, tvtime ne me r=C3=A9cup=C3=A8re aucune cha=C3=AEne ana=
logique et rien en num=C3=A9rique avec Kafeine.
Je pr=C3=A9cise que je suis sur Rennes et que j'ai du modifier le fichier ~=
/.kde/share/apps/kaffeine/dvb-t/fr-Rennes (selon la doc fournie ici : http:=
//gulliver.eu.org/wiki/TNT ).

j'ai =C3=A9galement essay=C3=A9 en cr=C3=A9ant un fichier /etc/modprobe.d/s=
aa7134 personalis=C3=A9 :
options saa7134 card=3D105 tuner=3D54 alsa=3D1=20
options saa7134-alsa index=3D1,2,3,4
Mais rien n'y fait.

Si quelqu'un a bien r=C3=A9ussi =C3=A0 faire fonctionner cette carte, j'aim=
erai profiter de cette exp=C3=A9rience.

merci,

----
Erwan