probl

Le
Carl Devos
Bonjour,

J'ai depuis quelques heures un problème avec le disque dur de mon Mac
Mini PPC (qui tourne etch):
Apr 4 14:06:01 localhost kernel: ide-pmac lost interrupt, dma status:
8400
Apr 4 14:06:01 localhost kernel: hda: lost interrupt
Apr 4 14:06:01 localhost kernel: hda: dma_intr: status=0x58
{ DriveReady SeekComplete DataRequest }
Apr 4 14:06:01 localhost kernel: ide: failed opcode was: unknown
Apr 4 14:06:01 localhost kernel: hda: status timeout: status=0xd0
{ Busy }
Apr 4 14:06:01 localhost kernel: ide: failed opcode was: unknown
Apr 4 14:06:01 localhost kernel: hda: DMA disabled
Apr 4 14:06:01 localhost kernel: hdb: DMA disabled
Apr 4 14:06:01 localhost kernel: hda: drive not ready for command
Apr 4 14:06:09 localhost kernel: ide0: reset: success

Jusqu'à ce que le reset ne fonctionne pas et la partition est remontée
en read-only et qu'il crashe.

Voici ce que donne smartmontools:

mjollnir:/home/carl# smartctl -a /dev/hda
smartctl version 5.36 [powerpc-unknown-linux-gnu] Copyright (C) 2002-6
Bruce Allen
Home page is http://smartmontools.sourceforge.net/

START OF INFORMATION SECTION
Model Family: Seagate Momentus 4200.2 Series
Device Model: ST9808210A
Serial Number: 3LF0VK9G
Firmware Version: 3.04
User Capacity: 80,026,361,856 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 2
Local Time is: Fri Apr 4 18:26:42 2008 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

START OF READ SMART DATA SECTION
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection:
Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon
new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test
supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging
support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 84) minutes.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 049 043 034 Pre-fail Always
- 28191970
3 Spin_Up_Time 0x0003 095 095 000 Pre-fail Always
- 0
4 Start_Stop_Count 0x0032 090 090 020 Old_age Always
- 10541
5 Reallocated_Sector_Ct 0x0033 095 095 036 Pre-fail Always
- 226
7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always
- 122981720
9 Power_On_Hours 0x0032 079 079 000 Old_age Always
- 18807
10 Spin_Retry_Count 0x0013 100 100 034 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always
- 706
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always
- 721
193 Load_Cycle_Count 0x0032 001 001 000 Old_age Always
- 4967562
194 Temperature_Celsius 0x0022 042 051 000 Old_age Always
- 42 (Lifetime Min/Max 0/15)
195 Hardware_ECC_Recovered 0x001a 049 043 000 Old_age Always
- 28191970
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
- 1
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age
Offline - 1
199 UDMA_CRC_Error_Count 0x003e 200 199 000 Old_age Always
- 32
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age
Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always
- 0

SMART Error Log Version: 1
ATA Error Count: 36 (device log contains only the most recent five
errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DDÚys, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 36 occurred at disk power-on lifetime: 18807 hours (783 days + 15
hours)
When the command that caused the error occurred, the device was active
or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 05 df d2 4c e0 Error: UNC at LBA = 0x004cd2df = 5034719

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- - --
24 00 08 dc d2 4c e0 00 00:24:15.035 READ SECTOR(S) EXT
24 00 08 04 90 4f e0 00 00:24:15.026 READ SECTOR(S) EXT
24 00 00 3e 13 5b e0 00 00:24:14.988 READ SECTOR(S) EXT
24 00 08 74 10 3a e0 00 00:24:14.985 READ SECTOR(S) EXT
24 00 08 64 c6 33 e0 00 00:24:14.982 READ SECTOR(S) EXT

Error 35 occurred at disk power-on lifetime: 18807 hours (783 days + 15
hours)
When the command that caused the error occurred, the device was active
or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 05 df d2 4c e0 Error: UNC at LBA = 0x004cd2df = 5034719

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- - --
24 00 08 dc d2 4c e0 00 00:24:07.699 READ SECTOR(S) EXT
24 00 08 54 9c 4f e0 00 00:24:07.688 READ SECTOR(S) EXT
24 00 08 6c 7b 4f e0 00 00:24:07.673 READ SECTOR(S) EXT
24 00 08 74 a8 4f e0 00 00:24:07.667 READ SECTOR(S) EXT
24 00 08 7c 9e 4f e0 00 00:24:07.784 READ SECTOR(S) EXT

Error 34 occurred at disk power-on lifetime: 18807 hours (783 days + 15
hours)
When the command that caused the error occurred, the device was active
or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 05 df d2 4c e0 Error: UNC at LBA = 0x004cd2df = 5034719

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- - --
24 00 08 dc d2 4c e0 00 00:24:00.153 READ SECTOR(S) EXT
24 00 08 24 8c 4f e0 00 00:24:00.146 READ SECTOR(S) EXT
24 00 08 54 8a 4f e0 00 00:24:00.143 READ SECTOR(S) EXT
24 00 08 8c 7d 4f e0 00 00:24:00.129 READ SECTOR(S) EXT
24 00 08 dc ac 4f e0 00 00:24:00.127 READ SECTOR(S) EXT

Error 33 occurred at disk power-on lifetime: 18807 hours (783 days + 15
hours)
When the command that caused the error occurred, the device was active
or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 15 df d2 4c e0 Error: UNC at LBA = 0x004cd2df = 5034719

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- - --
24 00 18 dc d2 4c e0 00 00:23:46.157 READ SECTOR(S) EXT
34 00 10 84 ae 4f e0 00 00:23:46.155 WRITE SECTORS(S) EXT
34 00 08 74 ae 4f e0 00 00:23:46.154 WRITE SECTORS(S) EXT
34 00 08 64 ae 4f e0 00 00:23:46.152 WRITE SECTORS(S) EXT
34 00 08 24 ae 4f e0 00 00:23:46.151 WRITE SECTORS(S) EXT

Error 32 occurred at disk power-on lifetime: 18807 hours (783 days + 15
hours)
When the command that caused the error occurred, the device was active
or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 7e 8e a5 e0 Error: UNC at LBA = 0x00a58e7e = 10849918

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- - --
25 00 1f 67 8e a5 e0 00 00:01:53.438 READ DMA EXT
25 00 20 66 8e a5 e0 00 00:01:52.545 READ DMA EXT
25 00 08 5e 8e a5 e0 00 00:01:52.456 READ DMA EXT
25 00 20 0e 8e a5 e0 00 00:01:52.456 READ DMA EXT
25 00 08 06 8e a5 e0 00 00:01:52.456 READ DMA EXT

SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]


SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute
delay.

J'ai lu sur http://lists.debian.org/debian-powerpc/2005/07/msg00279.html
(ou
http://groups.google.co.uk/group/linux.debian.ports.powerpc/browse_frm/thread/f12646d58f5f7b23/cfae90a4cc189071%23cfae90a4cc189071%5D)
que c'était peut-être un problème avec UMDA/4, mais je n'ai jamais eu
cela auparavant.

Quelqu'un peut me dépanner?

Merci,

--
Carl

--
Lisez la FAQ de la liste avant de poser une question :
http://wiki.debian.org/DebFrFrenchLists
Vous pouvez aussi ajouter le mot ``spam'' dans vos champs "From" et
"Reply-To:"

To UNSUBSCRIBE, email to debian-user-french-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Vidéos High-Tech et Jeu Vidéo
Téléchargements
Vos réponses
Gagnez chaque mois un abonnement Premium avec GNT : Inscrivez-vous !
Trier par : date / pertinence
Sylvain Sauvage
Le #9693491
Carl Devos, vendredi 4 avril 2008, 20:15:37 CEST

Bonjour,



’jour,

J'ai depuis quelques heures un problème avec le disque dur de mon Mac
Mini PPC (qui tourne etch):
[…]
1 Raw_Read_Error_Rate 0x000f 049 043 034 Pre-fail Always
- 28191970



Ouille !

3 Spin_Up_Time 0x0003 095 095 000 Pre-fail Always
- 0
4 Start_Stop_Count 0x0032 090 090 020 Old_age Always
- 10541



10 541 démarrages « softs »

5 Reallocated_Sector_Ct 0x0033 095 095 036 Pre-fail Always
- 226



226 secteurs réalloués (donc foutus).

7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always
- 122981720



Ouille.

9 Power_On_Hours 0x0032 079 079 000 Old_age Always
- 18807



18 807 heures de vol, 783 jours à temps plein, soit juste un
peu plus de deux ans. C’est pas forcément énorme.

10 Spin_Retry_Count 0x0013 100 100 034 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always
- 706



Démarré 706 fois.

192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always
- 721
193 Load_Cycle_Count 0x0032 001 001 000 Old_age Always
- 4967562



Ouille ouille ouille. Un disque peut en gros durer jusqu’à un
load cycle count de 3 millions ou 6 millions (ça dépend de l⠀™usage
prévu).
5 millions, ça fait beaucoup.

La valeur peut parfois être fantaisiste mais vu les autres
données, ton disque est vieux, et c’est donc cohérent.

http://en.wikipedia.org/wiki/S.M.A.R.T. permet de comprendre
les champs (en tout cas de savoir s’il faut s’inquiéte r ou pas).

[…]
J'ai lu sur http://lists.debian.org/debian-powerpc/2005/07/msg00279.html
(ou
http://groups.google.co.uk/group/linux.debian.ports.powerpc/browse_frm/th read/f12646d58f5f7b23/cfae90a4cc189071%23cfae90a4cc189071%5D)
que c'était peut-être un problème avec UMDA/4, mais je n'a i jamais eu
cela auparavant.



Ça m’a plutôt l’air des derniers râles d ’un disque fatigué.

Quelqu'un peut me dépanner?



Ton vendeur préféré de disques neufs.

Dépêche-toi tant que tu peux encore y lire tes données pour
mettre à jour tes sauvegardes.

--
Sylvain Sauvage
Publicité
Poster une réponse
Anonyme