ADSL Max et Wic ADSL Cisco

SkyFoxXP

29/12/2005 à 15:18

"JustMe" wrote in message
news:

Bonjour

Quelqu'un a t'il cette config ?

Je n'ai pas de synchro sur le cisco alors qu'un (bete) STH fonctionne tres
bien... Existe t'il une limite sur le WIC1-ADSL ou un reglage a faire ?

Question "bete" : avez-vous bien fait un "no shut" de l'interface ATM? ;-)

Le voyant CD est-il allumé sur la partie métallique du WIC?

Dans quel routeur avez-vous inséré cette WIC? Est-elle bien reconnue par le
routeur (show ver)?

Quel est le résultat de la commande "show dsl interface atm x/x"?

Postez votre configuration de manière à ce que l'on voit ce qui ne
fonctionne pas. Cela dit, quelque soit la configuration de la carte (même
vierge), le voyant CD devrait s'allumer quand meme.

JustMe

29/12/2005 à 16:03

"JustMe" wrote in message
news:
Bonjour

Quelqu'un a t'il cette config ?

Je n'ai pas de synchro sur le cisco alors qu'un (bete) STH fonctionne tres
bien... Existe t'il une limite sur le WIC1-ADSL ou un reglage a faire ?

Question "bete" : avez-vous bien fait un "no shut" de l'interface ATM? ;-)

oui ;-)

En fait ca marchait tres bien en 1024/128 mais au passage en ADSLmax
(5Mb/s environ) : plus de CD..

Le voyant CD est-il allumé sur la partie métallique du WIC?

non

Dans quel routeur avez-vous inséré cette WIC? Est-elle bien reconnue par le
routeur (show ver)?

Cisco 3640, dans un NM-1FE-2W tout marchait en 1024/128

Quel est le résultat de la commande "show dsl interface atm x/x"?

je rebranche ce soir et je reposte le resultat

Postez votre configuration de manière à ce que l'on voit ce qui ne fonctionne
pas. Cela dit, quelque soit la configuration de la carte (même vierge), le
voyant CD devrait s'allumer quand meme.

Ben non, ah marche pas :-(

Je vais aussi changer le cable filtre=>carte (c'etait du plat sur 1m
mais jen'y crois pas trop).

Pensez vous que la sensibilité du STH soit (bien) meilleure que celle
du WIC ?

Pour info degrouptest me donne les infos théoriques suivantes (plutot
bonnes) :

Longueur de ligne : 662 mtres
Affaiblissement : 9.93 dB
[Estimation] Dbit descendant ADSL : 8182 kbps (1023 ko/s)
[Estimation] Dbit descendant ADSL 2+ : 25334 kbps (3167 ko/s)

J'avais fait jadis les tests avec alcatool mais je ne retrouve plus les
resultats :-( Je vais le reinstaller ce soir et refaire le test

SkyFoxXP

29/12/2005 à 16:32

Je vous conseille de mettre à jour l'IOS du routeur.

j'ai déja constaté ce phénomene (sur des Cisco 827) : perte de synchro sur
des liens ADSL Max, résolus par l'installation d'un IOS plus récent.

Soit dit en passant, le WIC-1ADSL n'est pas officiellement compatible avec
l'ADSL Max ou avec le 2+.

Bon courage!

JustMe

29/12/2005 à 16:40

Il se trouve que SkyFoxXP a formulé :

Je vous conseille de mettre à jour l'IOS du routeur.

ok

j'ai déja constaté ce phénomene (sur des Cisco 827) : perte de synchro sur
des liens ADSL Max, résolus par l'installation d'un IOS plus récent.

bizarre

Soit dit en passant, le WIC-1ADSL n'est pas officiellement compatible avec
l'ADSL Max ou avec le 2+.

Pour le 2+ je comprend c'est une autre techno, mais pour l'ADSL max :
c'est de la techno ADSL1 de base, non ? le nom de "max" est juste
"marketing"

Quelle est la limite de vitesse officiellement supportee par le
WIC-1ADSL ?

SkyFoxXP

29/12/2005 à 18:35

Pour le 2+ je comprend c'est une autre techno, mais pour l'ADSL max :
c'est de la techno ADSL1 de base, non ? le nom de "max" est juste
"marketing"

Quelle est la limite de vitesse officiellement supportee par le WIC-1ADSL
?

Normalement, il supporte le 8800K / 880K.

JustMe

29/12/2005 à 22:19

SkyFoxXP a émis l'idée suivante :

Pour le 2+ je comprend c'est une autre techno, mais pour l'ADSL max : c'est
de la techno ADSL1 de base, non ? le nom de "max" est juste "marketing"

Quelle est la limite de vitesse officiellement supportee par le WIC-1ADSL ?

Normalement, il supporte le 8800K / 880K.

Bon je suis passe en 12.4-3b avec la feature ADSL

Le CD clignote et la ligne monte et descend regulierement

le sh dsl interface atm 0/0 donne :

ATM0/0
Alcatel 20150 chipset information
Line not activated: displaying cached data from last activation
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_DO_OPEN)
DSL Mode: ITU G.992.1 (G.DMT) Annex A
ITU STD NUM: 0x01 0x1
Vendor ID: 'ALCB' ' '
Vendor Specific: 0x0000 0x0000
Vendor Country: 0x00 0x00
Capacity Used: 98% 100%
Noise Margin: 5.5 dB 6.0 dB
Output Power: 14.0 dBm 12.0 dBm
Attenuation: 16.0 dB 11.0 dB
Defect Status: LCDi None
Last Fail Code: Handshake or init message invalid or had bad CRC
Selftest Result: 0x00
Subfunction: 0x15
Interrupts: 2743 (0 spurious)
PHY Access Err: 0
Activations: 16
LED Status: ON
LED On Time: 100
LED Off Time: 100
Init FW: embedded
Operation FW: embedded
SW Version: 3.8131
FW Version: 0x1A04

Interleave Fast Interleave
Fast
Speed (kbps): 7808 0 864
0
Cells: 0 0 0
0
Reed-Solomon EC: 0 0 0
0
CRC Errors: 0 0 0
0
Header Errors: 0 0 0
0
Bit Errors: 0 0
BER Valid sec: 0 0
BER Invalid sec: 0 0

LOM Monitoring : Disabled

DMT Bits Per Bin
00: 0 0 0 0 0 0 0 8 8 9 A B C C C C
10: C C D C B C C B B B A 9 9 9 0 0
20: 0 0 0 0 0 0 0 7 7 8 8 9 A A A A
30: A A A A A A A B B B B B C C C C
40: 0 C C C C C C C C C C C C C C C
50: C C C C C C C 2 C C C C C C C C
60: C C C C C C C C C C C B C B B B
70: B B B B B B B B B B B B B B B B
80: B B B B B B B B B B B B B B B B
90: B B B B B B B B B B B B B B B B
A0: B B B B B B B B B B B B B B B B
B0: B B B B B B B B B A B B B A A 8
C0: 8 8 9 8 9 8 8 7 4 6 8 8 8 8 8 8
D0: 9 8 9 8 8 8 9 8 8 8 8 8 8 8 8 8
E0: 8 8 8 8 8 8 8 8 8 8 8 8 7 7 6 5
F0: 4 3 2 3 2 2 0 0 0 0 0 0 0 0 0 0

DSL: Training log buffer capability is not enabled

------------------------------------------------------------------------

quant à la config elle ressemble a ca :

interface ATM0/0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto

.../...

interface Dialer0
mtu 1524
ip address negotiated
ip access-group 110 in
ip access-group 120 out
no ip redirects
no ip unreachables
ip nat outside
ip virtual-reassembly
encapsulation ppp
ip tcp header-compression
no ip mroute-cache
dialer pool 1
priority-group 1
no cdp enable
ppp authentication chap pap callin
ppp chap hostname fti/xxxxx
ppp chap password 7 xxxxx
ppp pap sent-username fti/xxxxx password 7 xxxxx
--------------------------------------------------------------------

Si ca te dit qq chose...

SkyFoxXP a émis l'idée suivante :

Pour le 2+ je comprend c'est une autre techno, mais pour l'ADSL max : c'est
de la techno ADSL1 de base, non ? le nom de "max" est juste "marketing"

Quelle est la limite de vitesse officiellement supportee par le WIC-1ADSL ?

Normalement, il supporte le 8800K / 880K.

Bon je suis passe en 12.4-3b avec la feature ADSL

Le CD clignote et la ligne monte et descend regulierement

le sh dsl interface atm 0/0 donne :

ATM0/0
Alcatel 20150 chipset information
Line not activated: displaying cached data from last activation
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_DO_OPEN)
DSL Mode: ITU G.992.1 (G.DMT) Annex A
ITU STD NUM: 0x01 0x1
Vendor ID: 'ALCB' ' '
Vendor Specific: 0x0000 0x0000
Vendor Country: 0x00 0x00
Capacity Used: 98% 100%
Noise Margin: 5.5 dB 6.0 dB
Output Power: 14.0 dBm 12.0 dBm
Attenuation: 16.0 dB 11.0 dB
Defect Status: LCDi None
Last Fail Code: Handshake or init message invalid or had bad CRC
Selftest Result: 0x00
Subfunction: 0x15
Interrupts: 2743 (0 spurious)
PHY Access Err: 0
Activations: 16
LED Status: ON
LED On Time: 100
LED Off Time: 100
Init FW: embedded
Operation FW: embedded
SW Version: 3.8131
FW Version: 0x1A04

Interleave Fast Interleave
Fast
Speed (kbps): 7808 0 864
0
Cells: 0 0 0
0
Reed-Solomon EC: 0 0 0
0
CRC Errors: 0 0 0
0
Header Errors: 0 0 0
0
Bit Errors: 0 0
BER Valid sec: 0 0
BER Invalid sec: 0 0

LOM Monitoring : Disabled

DMT Bits Per Bin
00: 0 0 0 0 0 0 0 8 8 9 A B C C C C
10: C C D C B C C B B B A 9 9 9 0 0
20: 0 0 0 0 0 0 0 7 7 8 8 9 A A A A
30: A A A A A A A B B B B B C C C C
40: 0 C C C C C C C C C C C C C C C
50: C C C C C C C 2 C C C C C C C C
60: C C C C C C C C C C C B C B B B
70: B B B B B B B B B B B B B B B B
80: B B B B B B B B B B B B B B B B
90: B B B B B B B B B B B B B B B B
A0: B B B B B B B B B B B B B B B B
B0: B B B B B B B B B A B B B A A 8
C0: 8 8 9 8 9 8 8 7 4 6 8 8 8 8 8 8
D0: 9 8 9 8 8 8 9 8 8 8 8 8 8 8 8 8
E0: 8 8 8 8 8 8 8 8 8 8 8 8 7 7 6 5
F0: 4 3 2 3 2 2 0 0 0 0 0 0 0 0 0 0

DSL: Training log buffer capability is not enabled

------------------------------------------------------------------------

quant à la config elle ressemble a ca :

interface ATM0/0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto

.../...

interface Dialer0
mtu 1524
ip address negotiated
ip access-group 110 in
ip access-group 120 out
no ip redirects
no ip unreachables
ip nat outside
ip virtual-reassembly
encapsulation ppp
ip tcp header-compression
no ip mroute-cache
dialer pool 1
priority-group 1
no cdp enable
ppp authentication chap pap callin
ppp chap hostname fti/xxxxx
ppp chap password 7 xxxxx
ppp pap sent-username fti/xxxxx password 7 xxxxx
--------------------------------------------------------------------

Si ca te dit qq chose...

Vous avez filtré cet utilisateur ! Consultez son message

SkyFoxXP a émis l'idée suivante :

Pour le 2+ je comprend c'est une autre techno, mais pour l'ADSL max : c'est
de la techno ADSL1 de base, non ? le nom de "max" est juste "marketing"

Quelle est la limite de vitesse officiellement supportee par le WIC-1ADSL ?

Normalement, il supporte le 8800K / 880K.

Bon je suis passe en 12.4-3b avec la feature ADSL

Le CD clignote et la ligne monte et descend regulierement

le sh dsl interface atm 0/0 donne :

ATM0/0
Alcatel 20150 chipset information
Line not activated: displaying cached data from last activation
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_DO_OPEN)
DSL Mode: ITU G.992.1 (G.DMT) Annex A
ITU STD NUM: 0x01 0x1
Vendor ID: 'ALCB' ' '
Vendor Specific: 0x0000 0x0000
Vendor Country: 0x00 0x00
Capacity Used: 98% 100%
Noise Margin: 5.5 dB 6.0 dB
Output Power: 14.0 dBm 12.0 dBm
Attenuation: 16.0 dB 11.0 dB
Defect Status: LCDi None
Last Fail Code: Handshake or init message invalid or had bad CRC
Selftest Result: 0x00
Subfunction: 0x15
Interrupts: 2743 (0 spurious)
PHY Access Err: 0
Activations: 16
LED Status: ON
LED On Time: 100
LED Off Time: 100
Init FW: embedded
Operation FW: embedded
SW Version: 3.8131
FW Version: 0x1A04

Interleave Fast Interleave
Fast
Speed (kbps): 7808 0 864
0
Cells: 0 0 0
0
Reed-Solomon EC: 0 0 0
0
CRC Errors: 0 0 0
0
Header Errors: 0 0 0
0
Bit Errors: 0 0
BER Valid sec: 0 0
BER Invalid sec: 0 0

LOM Monitoring : Disabled

DMT Bits Per Bin
00: 0 0 0 0 0 0 0 8 8 9 A B C C C C
10: C C D C B C C B B B A 9 9 9 0 0
20: 0 0 0 0 0 0 0 7 7 8 8 9 A A A A
30: A A A A A A A B B B B B C C C C
40: 0 C C C C C C C C C C C C C C C
50: C C C C C C C 2 C C C C C C C C
60: C C C C C C C C C C C B C B B B
70: B B B B B B B B B B B B B B B B
80: B B B B B B B B B B B B B B B B
90: B B B B B B B B B B B B B B B B
A0: B B B B B B B B B B B B B B B B
B0: B B B B B B B B B A B B B A A 8
C0: 8 8 9 8 9 8 8 7 4 6 8 8 8 8 8 8
D0: 9 8 9 8 8 8 9 8 8 8 8 8 8 8 8 8
E0: 8 8 8 8 8 8 8 8 8 8 8 8 7 7 6 5
F0: 4 3 2 3 2 2 0 0 0 0 0 0 0 0 0 0

DSL: Training log buffer capability is not enabled

------------------------------------------------------------------------

quant à la config elle ressemble a ca :

interface ATM0/0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto

.../...

interface Dialer0
mtu 1524
ip address negotiated
ip access-group 110 in
ip access-group 120 out
no ip redirects
no ip unreachables
ip nat outside
ip virtual-reassembly
encapsulation ppp
ip tcp header-compression
no ip mroute-cache
dialer pool 1
priority-group 1
no cdp enable
ppp authentication chap pap callin
ppp chap hostname fti/xxxxx
ppp chap password 7 xxxxx
ppp pap sent-username fti/xxxxx password 7 xxxxx
--------------------------------------------------------------------

Si ca te dit qq chose...

JustMe

29/12/2005 à 23:08

PS

J'ai mis en debug pour voir : ca donne ca :

*Sep 2 19:39:01.985 MET-DST: ATM0/0 dslsar_1a_reset: PLIM type is 18,
Rate is 8
96Mbps
*Sep 2 19:39:01.985 MET-DST: ATM0/0 dslsar_1a_shutdown: state=4
*Sep 2 19:39:01.985 MET-DST: dslsar disable ATM0/0

*Sep 2 19:39:01.985 MET-DST: DSL: SET: [DMTDSL_STOP -> DMTDSL_INIT]
*Sep 2 19:39:01.985 MET-DST: Resetting ATM0/0
*Sep 2 19:39:01.989 MET-DST: dslsar_1a_config(ATM0/0)
*Sep 2 19:39:01.989 MET-DST: dslsar_1a_enable(ATM0/0)
*Sep 2 19:39:02.013 MET-DST: ATM0/0: dslsar_init
*Sep 2 19:39:02.021 MET-DST: ATM0/0 dslsar_MatchSARTxToLineSpeed():
usbw 896, c
lkPerCell 16718 prev_clkPerCell 9702
*Sep 2 19:39:02.021 MET-DST: ATM0/0 dslsar_MatchSARTxToLineSpeed():
Changing li
ne speed from fast to slow
*Sep 2 19:39:02.133 MET-DST: ATM0/0 dslsar_update_us_bandwidth():
upstream bw 896 Kbps
*Sep 2 19:39:02.645 MET-DST: DSL: SM: [DMTDSL_STOP -> DMTDSL_INIT]
*Sep 2 19:39:02.649 MET-DST: DSL: SM: [DMTDSL_INIT -> DMTDSL_DLOAD_1]
*Sep 2 19:39:02.653 MET-DST: DSL: Downloading ASW_init_3_8_131.bin
*Sep 2 19:39:02.685 MET-DST: DSL:(ATM0/0) Downloaded 5 blocks...
Finished!
*Sep 2 19:39:02.689 MET-DST: DSL(ATM0/0): Sent command 0x14
*Sep 2 19:39:03.985 MET-DST: %LINK-3-UPDOWN: Interface ATM0/0, changed
state to
down
*Sep 2 19:39:03.985 MET-DST: dslsar_atm_lineaction(ATM0/0): state=0
*Sep 2 19:39:06.597 MET-DST: DSL: Received response: 0x80
*Sep 2 19:39:06.597 MET-DST: DSL: SM: [DMTDSL_DLOAD_1 ->
DMTDSL_DLOAD_2]
*Sep 2 19:39:06.817 MET-DST: DSL: Downloading ASW_R3_8_131.bin
*Sep 2 19:39:07.529 MET-DST: DSL(ATM0/0): Downloaded 100 blocks
*Sep 2 19:39:08.249 MET-DST: DSL(ATM0/0): Downloaded 200 blocks
*Sep 2 19:39:08.965 MET-DST: DSL(ATM0/0): Downloaded 300 blocks
*Sep 2 19:39:09.681 MET-DST: DSL(ATM0/0): Downloaded 400 blocks
*Sep 2 19:39:10.397 MET-DST: DSL(ATM0/0): Downloaded 500 blocks
*Sep 2 19:39:11.117 MET-DST: DSL(ATM0/0): Downloaded 600 blocks
*Sep 2 19:39:11.833 MET-DST: DSL(ATM0/0): Downloaded 700 blocks
*Sep 2 19:39:12.549 MET-DST: DSL(ATM0/0): Downloaded 800 blocks
*Sep 2 19:39:13.269 MET-DST: DSL(ATM0/0): Downloaded 900 blocks
*Sep 2 19:39:13.989 MET-DST: DSL(ATM0/0): Downloaded 1000 blocks
*Sep 2 19:39:14.701 MET-DST: DSL(ATM0/0): Downloaded 1100 blocks
*Sep 2 19:39:15.413 MET-DST: DSL(ATM0/0): Downloaded 1200 blocks
*Sep 2 19:39:16.133 MET-DST: DSL(ATM0/0): Downloaded 1300 blocks
*Sep 2 19:39:16.249 MET-DST: DSL:(ATM0/0) Downloaded 1317 blocks...
Finished!
*Sep 2 19:39:16.249 MET-DST: DSL(ATM0/0): Sent command 0x14
*Sep 2 19:39:18.257 MET-DST: set tx_gain_offset to 0
*Sep 2 19:39:18.257 MET-DST: set rx_gain_offset to 0
*Sep 2 19:39:18.257 MET-DST: set target_noise_margin_offset to 0
*Sep 2 19:39:18.257 MET-DST: set max_bits_tone_limit to 14
*Sep 2 19:39:18.257 MET-DST: changed current state to do open!!
*Sep 2 19:39:18.257 MET-DST: DSL: SM: [DMTDSL_DLOAD_2 ->
DMTDSL_DO_OPEN]
*Sep 2 19:39:18.257 MET-DST: DSL: Send ADSL_OPEN command.
*Sep 2 19:39:18.261 MET-DST: DSL(ATM0/0): Using subfunction 0x15
*Sep 2 19:39:18.261 MET-DST: LOCAL:Max noise margin for power cutoff
31
*Sep 2 19:39:18.261 MET-DST: DSL(ATM0/0): Sent command 0x3
*Sep 2 19:39:20.761 MET-DST: DSL(ATM0/0): 1: Modem state = 0x8
*Sep 2 19:39:23.261 MET-DST: DSL(ATM0/0): 2: Modem state = 0x10
*Sep 2 19:39:25.761 MET-DST: DSL(ATM0/0): 3: Modem state = 0x10
*Sep 2 19:39:28.261 MET-DST: DSL(ATM0/0): 4: Modem state = 0x10
*Sep 2 19:39:29.633 MET-DST: DSL: Received response: 0x22
*Sep 2 19:39:29.633 MET-DST: DSL: Open failed: Handshake or init
message invali
d or had bad CRC -- retrying
*Sep 2 19:39:29.633 MET-DST: sleep 5 seconds
*Sep 2 19:39:34.632 MET-DST: DSL: Send ADSL_OPEN command.
*Sep 2 19:39:34.632 MET-DST: DSL(ATM0/0): Using subfunction 0x15
*Sep 2 19:39:34.632 MET-DST: LOCAL:Max noise margin for power cutoff
31
*Sep 2 19:39:34.632 MET-DST: DSL(ATM0/0): Sent command 0x3
*Sep 2 19:39:37.132 MET-DST: DSL(ATM0/0): 1: Modem state = 0x8
*Sep 2 19:39:39.632 MET-DST: DSL(ATM0/0): 2: Modem state = 0x10
*Sep 2 19:39:42.132 MET-DST: DSL(ATM0/0): 3: Modem state = 0x10
*Sep 2 19:39:44.632 MET-DST: DSL(ATM0/0): 4: Modem state = 0x10
*Sep 2 19:39:47.132 MET-DST: DSL(ATM0/0): 5: Modem state = 0x10
*Sep 2 19:39:47.384 MET-DST: DSL: Received response: 0x24
*Sep 2 19:39:47.384 MET-DST: DSL: Showtime!
*Sep 2 19:39:47.384 MET-DST: DSL(ATM0/0): Sent command 0x11
*Sep 2 19:39:47.388 MET-DST: DSL: Received response: 0x61
*Sep 2 19:39:47.388 MET-DST: DSL: Read firmware revision 0x1A04
*Sep 2 19:39:47.388 MET-DST: DSL(ATM0/0): Sent command 0x31
*Sep 2 19:39:47.392 MET-DST: DSL: Received response: 0x12
*Sep 2 19:39:47.396 MET-DST: DSL(ATM0/0): operation mode 0x0002
*Sep 2 19:39:47.396 MET-DST: DSL(ATM0/0): Sent command 0x33
*Sep 2 19:39:47.400 MET-DST: DSL: Received response: 0x16
*Sep 2 19:39:47.400 MET-DST: DSL(ATM0/0): Far End ITU Country Code
0x00
*Sep 2 19:39:47.400 MET-DST: DSL: Far End ITU Vendor ID
*Sep 2 19:39:47.400 MET-DST: DSL: Far End ITU Vendor ID Specific
0x0000
*Sep 2 19:39:47.400 MET-DST: DSL: Far End ITU Vendor STD Number 0x0001
*Sep 2 19:39:47.400 MET-DST: DSL(ATM0/0): Sent command 0x32
*Sep 2 19:39:47.404 MET-DST: DSL: Received response: 0x14
*Sep 2 19:39:47.404 MET-DST: DSL(ATM0/0): Near End ITU Country Code
0x00
*Sep 2 19:39:47.404 MET-DST: DSL: Near End ITU Vendor ID ALCB
*Sep 2 19:39:47.404 MET-DST: DSL: Near End ITU Vendor ID Specific
0x0000
*Sep 2 19:39:47.404 MET-DST: DSL: Near End ITU Vendor STD Number
0x0001
*Sep 2 19:39:47.404 MET-DST: ATM0/0 dslsar_MatchSARTxToLineSpeed():
usbw 864, c
lkPerCell 17337 prev_clkPerCell 16718
*Sep 2 19:39:47.408 MET-DST: ATM0/0 dslsar_MatchSARTxToLineSpeed():
Changing li
ne speed from fast to slow
*Sep 2 19:39:47.516 MET-DST: ATM0/0 dslsar_update_us_bandwidth():
upstream bw 864 Kbps
*Sep 2 19:39:47.520 MET-DST: DSL: SM: [DMTDSL_DO_OPEN ->
DMTDSL_SHOWTIME]
*Sep 2 19:39:49.956 MET-DST: dslsar_periodic: ENABLING DSLSAR

*Sep 2 19:39:50.032 MET-DST: DSL: Defect: LCDi: retraining
*Sep 2 19:39:51.668 MET-DST: dslsar enable ATM0/0

*Sep 2 19:39:51.668 MET-DST: ATM0/0: dslsar_bringup_interface:
Interface and at
m_db flags are UP
*Sep 2 19:39:52.544 MET-DST: DSL: SM: [DMTDSL_SHOWTIME ->
DMTDSL_RE_OPEN]
*Sep 2 19:39:52.548 MET-DST: DSL: Send ADSL_CLOSE command.
*Sep 2 19:39:52.548 MET-DST: DSL(ATM0/0): Sent command 0x4
*Sep 2 19:39:52.568 MET-DST: ATM0/0 check_lockup: scc = 0,
output_qcount = 0, h
ead:(s)1, 1,
addr = (s)0x0, 0x0, count (s)0, 0
*Sep 2 19:39:52.568 MET-DST: ATM0/0 check_lockup: scc = 1,
output_qcount = 0, h
ead:(s)50, 49,
addr = (s)0x0, 0x64D966F0, count (s)494, 545
*Sep 2 19:39:53.072 MET-DST: DSL: Received response: 0x25
*Sep 2 19:39:53.072 MET-DST: DSL: Connection closed
*Sep 2 19:39:53.076 MET-DST: DSL: SM: [DMTDSL_RE_OPEN ->
DMTDSL_DO_OPEN]
*Sep 2 19:39:53.076 MET-DST: DSL: Send ADSL_OPEN command.
*Sep 2 19:39:53.076 MET-DST: DSL(ATM0/0): Using subfunction 0x15
*Sep 2 19:39:53.080 MET-DST: LOCAL:Max noise margin for power cutoff
31
*Sep 2 19:39:53.080 MET-DST: DSL(ATM0/0): Sent command 0x3
*Sep 2 19:39:53.668 MET-DST: %LINK-3-UPDOWN: Interface ATM0/0, changed
state to
up
*Sep 2 19:39:53.668 MET-DST: dslsar_atm_lineaction(ATM0/0): state=4
*Sep 2 19:39:54.668 MET-DST: %LINEPROTO-5-UPDOWN: Line protocol on
Interface AT
M0/0, changed state to up
*Sep 2 19:39:55.580 MET-DST: DSL(ATM0/0): 1: Modem state = 0x8
*Sep 2 19:39:58.080 MET-DST: DSL(ATM0/0): 2: Modem state = 0x8
*Sep 2 19:39:59.956 MET-DST: dslsar disable ATM0/0

*Sep 2 19:40:00.580 MET-DST: DSL(ATM0/0): 3: Modem state = 0x8
*Sep 2 19:40:01.956 MET-DST: %LINK-3-UPDOWN: Interface ATM0/0, changed
state to
down
*Sep 2 19:40:01.956 MET-DST: dslsar_atm_lineaction(ATM0/0): state=0
*Sep 2 19:40:02.956 MET-DST: %LINEPROTO-5-UPDOWN: Line protocol on
Interface AT
M0/0, changed state to down
*Sep 2 19:40:03.080 MET-DST: DSL(ATM0/0): 4: Modem state = 0x8
*Sep 2 19:40:05.580 MET-DST: DSL(ATM0/0): 5: Modem state = 0x8
*Sep 2 19:40:08.080 MET-DST: DSL(ATM0/0): 6: Modem state = 0x10
*Sep 2 19:40:10.580 MET-DST: DSL(ATM0/0): 7: Modem state = 0x10
*Sep 2 19:40:13.080 MET-DST: DSL(ATM0/0): 8: Modem state = 0x10
*Sep 2 19:40:14.392 MET-DST: DSL: Received response: 0x24
*Sep 2 19:40:14.392 MET-DST: DSL: Showtime!
*Sep 2 19:40:14.392 MET-DST: DSL(ATM0/0): Sent command 0x11
*Sep 2 19:40:14.396 MET-DST: DSL: Received response: 0x61
*Sep 2 19:40:14.396 MET-DST: DSL: Read firmware revision 0x1A04
*Sep 2 19:40:14.396 MET-DST: DSL(ATM0/0): Sent command 0x31
*Sep 2 19:40:14.404 MET-DST: DSL: Received response: 0x12
*Sep 2 19:40:14.404 MET-DST: DSL(ATM0/0): operation mode 0x0002
*Sep 2 19:40:14.404 MET-DST: DSL(ATM0/0): Sent command 0x33
*Sep 2 19:40:14.408 MET-DST: DSL: Received response: 0x16
*Sep 2 19:40:14.408 MET-DST: DSL(ATM0/0): Far End ITU Country Code
0x00
*Sep 2 19:40:14.408 MET-DST: DSL: Far End ITU Vendor ID
*Sep 2 19:40:14.408 MET-DST: DSL: Far End ITU Vendor ID Specific
0x0000
*Sep 2 19:40:14.408 MET-DST: DSL: Far End ITU Vendor STD Number 0x0001
*Sep 2 19:40:14.408 MET-DST: DSL(ATM0/0): Sent command 0x32
*Sep 2 19:40:14.412 MET-DST: DSL: Received response: 0x14
*Sep 2 19:40:14.412 MET-DST: DSL(ATM0/0): Near End ITU Country Code
0x00
*Sep 2 19:40:14.412 MET-DST: DSL: Near End ITU Vendor ID ALCB
*Sep 2 19:40:14.412 MET-DST: DSL: Near End ITU Vendor ID Specific
0x0000
*Sep 2 19:40:14.416 MET-DST: DSL: Near End ITU Vendor STD Number
0x0001
*Sep 2 19:40:14.416 MET-DST: ATM0/0 dslsar_MatchSARTxToLineSpeed():
usbw 864, c
lkPerCell 17337 prev_clkPerCell 17337
*Sep 2 19:40:14.416 MET-DST: ATM0/0 dslsar_update_us_bandwidth():
upstream bw 864 Kbps
*Sep 2 19:40:14.416 MET-DST: DSL: SM: [DMTDSL_DO_OPEN ->
DMTDSL_SHOWTIME]
*Sep 2 19:40:19.440 MET-DST: DSL: Defect: LCDi: retraining
*Sep 2 19:40:19.956 MET-DST: dslsar_periodic: ENABLING DSLSAR

*Sep 2 19:40:21.668 MET-DST: dslsar enable ATM0/0

*Sep 2 19:40:21.668 MET-DST: ATM0/0: dslsar_bringup_interface:
Interface and at
m_db flags are UP
*Sep 2 19:40:21.952 MET-DST: DSL: SM: [DMTDSL_SHOWTIME ->
DMTDSL_RE_OPEN]
*Sep 2 19:40:21.956 MET-DST: DSL: Send ADSL_CLOSE command.
*Sep 2 19:40:21.956 MET-DST: DSL(ATM0/0): Sent command 0x4
*Sep 2 19:40:22.400 MET-DST: ATM0/0 check_lockup: scc = 0,
output_qcount = 0, h
ead:(s)1, 1,
addr = (s)0x0, 0x0, count (s)0, 0
*Sep 2 19:40:22.400 MET-DST: ATM0/0 check_lockup: scc = 1,
output_qcount = 0, h
ead:(s)49, 74,
addr = (s)0x64D966F0, 0x0, count (s)545, 567
*Sep 2 19:40:22.480 MET-DST: DSL: Received response: 0x25
*Sep 2 19:40:22.480 MET-DST: DSL: Connection closed
*Sep 2 19:40:22.488 MET-DST: DSL: SM: [DMTDSL_RE_OPEN ->
DMTDSL_DO_OPEN]
*Sep 2 19:40:22.488 MET-DST: DSL: Send ADSL_OPEN command.
*Sep 2 19:40:22.492 MET-DST: DSL(ATM0/0): Using subfunction 0x15
*Sep 2 19:40:22.492 MET-DST: LOCAL:Max noise margin for power cutoff
31
*Sep 2 19:40:22.492 MET-DST: DSL(ATM0/0): Sent command 0x3
*Sep 2 19:40:23.668 MET-DST: %LINK-3-UPDOWN: Interface ATM0/0, changed
state to
up
*Sep 2 19:40:23.668 MET-DST: dslsar_atm_lineaction(ATM0/0): state=4
*Sep 2 19:40:24.668 MET-DST: %LINEPROTO-5-UPDOWN: Line protocol on
Interface AT
M0/0, changed state to up
*Sep 2 19:40:24.992 MET-DST: DSL(ATM0/0): 1: Modem state = 0x8
*Sep 2 19:40:27.492 MET-DST: DSL(ATM0/0): 2: Modem state = 0x8
*Sep 2 19:40:29.956 MET-DST: dslsar disable ATM0/0

*Sep 2 19:40:29.992 MET-DST: DSL(ATM0/0): 3: Modem state = 0x8
*Sep 2 19:40:31.956 MET-DST: %LINK-3-UPDOWN: Interface ATM0/0, changed
state to
down
*Sep 2 19:40:31.956 MET-DST: dslsar_atm_lineaction(ATM0/0): state=0
*Sep 2 19:40:32.492 MET-DST: DSL(ATM0/0): 4: Modem state = 0x8
*Sep 2 19:40:32.956 MET-DST: %LINEPROTO-5-UPDOWN: Line protocol on
Interface AT
M0/0, changed state to down
*Sep 2 19:40:34.991 MET-DST: DSL(ATM0/0): 5: Modem state = 0x8
*Sep 2 19:40:36.119 MET-DST: ATM0/0 dslsar_1a_shutdown: state=6
*Sep 2 19:40:36.119 MET-DST: dslsar disable ATM0/0

*Sep 2 19:40:36.119 MET-DST: DSL: SET: [DMTDSL_DO_OPEN -> DMTDSL_STOP]
*Sep 2 19:40:36.123 MET-DST: Resetting ATM0/0
*Sep 2 19:40:37.491 MET-DST: DSL: SM: [DMTDSL_DO_OPEN -> DMTDSL_STOP]
*Sep 2 19:40:38.119 MET-DST: %LINK-5-CHANGED: Interface ATM0/0,
changed state t
o administratively down
*Sep 2 19:40:38.119 MET-DST: dslsar_atm_lineaction(ATM0/0): state=6
*Sep 2 19:40:44.491 MET-DST: DSL(ATM0/0): Sent command 0x4
*Sep 2 19:40:44.491 MET-DST: DSL: Received response: 0x24
*Sep 2 19:40:44.491 MET-DST: DSL: Unexpected response 0x24
*Sep 2 19:40:44.991 MET-DST: DSL(ATM0/0): Sent command 0x4
*Sep 2 19:40:45.011 MET-DST: DSL: Received response: 0x25
*Sep 2 19:40:45.011 MET-DST: DSL(ATM0/0): Connection closed

Vous avez filtré cet utilisateur ! Consultez son message

PS

J'ai mis en debug pour voir : ca donne ca :

*Sep 2 19:39:01.985 MET-DST: ATM0/0 dslsar_1a_reset: PLIM type is 18,
Rate is 8
96Mbps
*Sep 2 19:39:01.985 MET-DST: ATM0/0 dslsar_1a_shutdown: state=4
*Sep 2 19:39:01.985 MET-DST: dslsar disable ATM0/0

*Sep 2 19:39:01.985 MET-DST: DSL: SET: [DMTDSL_STOP -> DMTDSL_INIT]
*Sep 2 19:39:01.985 MET-DST: Resetting ATM0/0
*Sep 2 19:39:01.989 MET-DST: dslsar_1a_config(ATM0/0)
*Sep 2 19:39:01.989 MET-DST: dslsar_1a_enable(ATM0/0)
*Sep 2 19:39:02.013 MET-DST: ATM0/0: dslsar_init
*Sep 2 19:39:02.021 MET-DST: ATM0/0 dslsar_MatchSARTxToLineSpeed():
usbw 896, c
lkPerCell 16718 prev_clkPerCell 9702
*Sep 2 19:39:02.021 MET-DST: ATM0/0 dslsar_MatchSARTxToLineSpeed():
Changing li
ne speed from fast to slow
*Sep 2 19:39:02.133 MET-DST: ATM0/0 dslsar_update_us_bandwidth():
upstream bw 896 Kbps
*Sep 2 19:39:02.645 MET-DST: DSL: SM: [DMTDSL_STOP -> DMTDSL_INIT]
*Sep 2 19:39:02.649 MET-DST: DSL: SM: [DMTDSL_INIT -> DMTDSL_DLOAD_1]
*Sep 2 19:39:02.653 MET-DST: DSL: Downloading ASW_init_3_8_131.bin
*Sep 2 19:39:02.685 MET-DST: DSL:(ATM0/0) Downloaded 5 blocks...
Finished!
*Sep 2 19:39:02.689 MET-DST: DSL(ATM0/0): Sent command 0x14
*Sep 2 19:39:03.985 MET-DST: %LINK-3-UPDOWN: Interface ATM0/0, changed
state to
down
*Sep 2 19:39:03.985 MET-DST: dslsar_atm_lineaction(ATM0/0): state=0
*Sep 2 19:39:06.597 MET-DST: DSL: Received response: 0x80
*Sep 2 19:39:06.597 MET-DST: DSL: SM: [DMTDSL_DLOAD_1 ->
DMTDSL_DLOAD_2]
*Sep 2 19:39:06.817 MET-DST: DSL: Downloading ASW_R3_8_131.bin
*Sep 2 19:39:07.529 MET-DST: DSL(ATM0/0): Downloaded 100 blocks
*Sep 2 19:39:08.249 MET-DST: DSL(ATM0/0): Downloaded 200 blocks
*Sep 2 19:39:08.965 MET-DST: DSL(ATM0/0): Downloaded 300 blocks
*Sep 2 19:39:09.681 MET-DST: DSL(ATM0/0): Downloaded 400 blocks
*Sep 2 19:39:10.397 MET-DST: DSL(ATM0/0): Downloaded 500 blocks
*Sep 2 19:39:11.117 MET-DST: DSL(ATM0/0): Downloaded 600 blocks
*Sep 2 19:39:11.833 MET-DST: DSL(ATM0/0): Downloaded 700 blocks
*Sep 2 19:39:12.549 MET-DST: DSL(ATM0/0): Downloaded 800 blocks
*Sep 2 19:39:13.269 MET-DST: DSL(ATM0/0): Downloaded 900 blocks
*Sep 2 19:39:13.989 MET-DST: DSL(ATM0/0): Downloaded 1000 blocks
*Sep 2 19:39:14.701 MET-DST: DSL(ATM0/0): Downloaded 1100 blocks
*Sep 2 19:39:15.413 MET-DST: DSL(ATM0/0): Downloaded 1200 blocks
*Sep 2 19:39:16.133 MET-DST: DSL(ATM0/0): Downloaded 1300 blocks
*Sep 2 19:39:16.249 MET-DST: DSL:(ATM0/0) Downloaded 1317 blocks...
Finished!
*Sep 2 19:39:16.249 MET-DST: DSL(ATM0/0): Sent command 0x14
*Sep 2 19:39:18.257 MET-DST: set tx_gain_offset to 0
*Sep 2 19:39:18.257 MET-DST: set rx_gain_offset to 0
*Sep 2 19:39:18.257 MET-DST: set target_noise_margin_offset to 0
*Sep 2 19:39:18.257 MET-DST: set max_bits_tone_limit to 14
*Sep 2 19:39:18.257 MET-DST: changed current state to do open!!
*Sep 2 19:39:18.257 MET-DST: DSL: SM: [DMTDSL_DLOAD_2 ->
DMTDSL_DO_OPEN]
*Sep 2 19:39:18.257 MET-DST: DSL: Send ADSL_OPEN command.
*Sep 2 19:39:18.261 MET-DST: DSL(ATM0/0): Using subfunction 0x15
*Sep 2 19:39:18.261 MET-DST: LOCAL:Max noise margin for power cutoff
31
*Sep 2 19:39:18.261 MET-DST: DSL(ATM0/0): Sent command 0x3
*Sep 2 19:39:20.761 MET-DST: DSL(ATM0/0): 1: Modem state = 0x8
*Sep 2 19:39:23.261 MET-DST: DSL(ATM0/0): 2: Modem state = 0x10
*Sep 2 19:39:25.761 MET-DST: DSL(ATM0/0): 3: Modem state = 0x10
*Sep 2 19:39:28.261 MET-DST: DSL(ATM0/0): 4: Modem state = 0x10
*Sep 2 19:39:29.633 MET-DST: DSL: Received response: 0x22
*Sep 2 19:39:29.633 MET-DST: DSL: Open failed: Handshake or init
message invali
d or had bad CRC -- retrying
*Sep 2 19:39:29.633 MET-DST: sleep 5 seconds
*Sep 2 19:39:34.632 MET-DST: DSL: Send ADSL_OPEN command.
*Sep 2 19:39:34.632 MET-DST: DSL(ATM0/0): Using subfunction 0x15
*Sep 2 19:39:34.632 MET-DST: LOCAL:Max noise margin for power cutoff
31
*Sep 2 19:39:34.632 MET-DST: DSL(ATM0/0): Sent command 0x3
*Sep 2 19:39:37.132 MET-DST: DSL(ATM0/0): 1: Modem state = 0x8
*Sep 2 19:39:39.632 MET-DST: DSL(ATM0/0): 2: Modem state = 0x10
*Sep 2 19:39:42.132 MET-DST: DSL(ATM0/0): 3: Modem state = 0x10
*Sep 2 19:39:44.632 MET-DST: DSL(ATM0/0): 4: Modem state = 0x10
*Sep 2 19:39:47.132 MET-DST: DSL(ATM0/0): 5: Modem state = 0x10
*Sep 2 19:39:47.384 MET-DST: DSL: Received response: 0x24
*Sep 2 19:39:47.384 MET-DST: DSL: Showtime!
*Sep 2 19:39:47.384 MET-DST: DSL(ATM0/0): Sent command 0x11
*Sep 2 19:39:47.388 MET-DST: DSL: Received response: 0x61
*Sep 2 19:39:47.388 MET-DST: DSL: Read firmware revision 0x1A04
*Sep 2 19:39:47.388 MET-DST: DSL(ATM0/0): Sent command 0x31
*Sep 2 19:39:47.392 MET-DST: DSL: Received response: 0x12
*Sep 2 19:39:47.396 MET-DST: DSL(ATM0/0): operation mode 0x0002
*Sep 2 19:39:47.396 MET-DST: DSL(ATM0/0): Sent command 0x33
*Sep 2 19:39:47.400 MET-DST: DSL: Received response: 0x16
*Sep 2 19:39:47.400 MET-DST: DSL(ATM0/0): Far End ITU Country Code
0x00
*Sep 2 19:39:47.400 MET-DST: DSL: Far End ITU Vendor ID
*Sep 2 19:39:47.400 MET-DST: DSL: Far End ITU Vendor ID Specific
0x0000
*Sep 2 19:39:47.400 MET-DST: DSL: Far End ITU Vendor STD Number 0x0001
*Sep 2 19:39:47.400 MET-DST: DSL(ATM0/0): Sent command 0x32
*Sep 2 19:39:47.404 MET-DST: DSL: Received response: 0x14
*Sep 2 19:39:47.404 MET-DST: DSL(ATM0/0): Near End ITU Country Code
0x00
*Sep 2 19:39:47.404 MET-DST: DSL: Near End ITU Vendor ID ALCB
*Sep 2 19:39:47.404 MET-DST: DSL: Near End ITU Vendor ID Specific
0x0000
*Sep 2 19:39:47.404 MET-DST: DSL: Near End ITU Vendor STD Number
0x0001
*Sep 2 19:39:47.404 MET-DST: ATM0/0 dslsar_MatchSARTxToLineSpeed():
usbw 864, c
lkPerCell 17337 prev_clkPerCell 16718
*Sep 2 19:39:47.408 MET-DST: ATM0/0 dslsar_MatchSARTxToLineSpeed():
Changing li
ne speed from fast to slow
*Sep 2 19:39:47.516 MET-DST: ATM0/0 dslsar_update_us_bandwidth():
upstream bw 864 Kbps
*Sep 2 19:39:47.520 MET-DST: DSL: SM: [DMTDSL_DO_OPEN ->
DMTDSL_SHOWTIME]
*Sep 2 19:39:49.956 MET-DST: dslsar_periodic: ENABLING DSLSAR

*Sep 2 19:39:50.032 MET-DST: DSL: Defect: LCDi: retraining
*Sep 2 19:39:51.668 MET-DST: dslsar enable ATM0/0

*Sep 2 19:39:51.668 MET-DST: ATM0/0: dslsar_bringup_interface:
Interface and at
m_db flags are UP
*Sep 2 19:39:52.544 MET-DST: DSL: SM: [DMTDSL_SHOWTIME ->
DMTDSL_RE_OPEN]
*Sep 2 19:39:52.548 MET-DST: DSL: Send ADSL_CLOSE command.
*Sep 2 19:39:52.548 MET-DST: DSL(ATM0/0): Sent command 0x4
*Sep 2 19:39:52.568 MET-DST: ATM0/0 check_lockup: scc = 0,
output_qcount = 0, h
ead:(s)1, 1,
addr = (s)0x0, 0x0, count (s)0, 0
*Sep 2 19:39:52.568 MET-DST: ATM0/0 check_lockup: scc = 1,
output_qcount = 0, h
ead:(s)50, 49,
addr = (s)0x0, 0x64D966F0, count (s)494, 545
*Sep 2 19:39:53.072 MET-DST: DSL: Received response: 0x25
*Sep 2 19:39:53.072 MET-DST: DSL: Connection closed
*Sep 2 19:39:53.076 MET-DST: DSL: SM: [DMTDSL_RE_OPEN ->
DMTDSL_DO_OPEN]
*Sep 2 19:39:53.076 MET-DST: DSL: Send ADSL_OPEN command.
*Sep 2 19:39:53.076 MET-DST: DSL(ATM0/0): Using subfunction 0x15
*Sep 2 19:39:53.080 MET-DST: LOCAL:Max noise margin for power cutoff
31
*Sep 2 19:39:53.080 MET-DST: DSL(ATM0/0): Sent command 0x3
*Sep 2 19:39:53.668 MET-DST: %LINK-3-UPDOWN: Interface ATM0/0, changed
state to
up
*Sep 2 19:39:53.668 MET-DST: dslsar_atm_lineaction(ATM0/0): state=4
*Sep 2 19:39:54.668 MET-DST: %LINEPROTO-5-UPDOWN: Line protocol on
Interface AT
M0/0, changed state to up
*Sep 2 19:39:55.580 MET-DST: DSL(ATM0/0): 1: Modem state = 0x8
*Sep 2 19:39:58.080 MET-DST: DSL(ATM0/0): 2: Modem state = 0x8
*Sep 2 19:39:59.956 MET-DST: dslsar disable ATM0/0

*Sep 2 19:40:00.580 MET-DST: DSL(ATM0/0): 3: Modem state = 0x8
*Sep 2 19:40:01.956 MET-DST: %LINK-3-UPDOWN: Interface ATM0/0, changed
state to
down
*Sep 2 19:40:01.956 MET-DST: dslsar_atm_lineaction(ATM0/0): state=0
*Sep 2 19:40:02.956 MET-DST: %LINEPROTO-5-UPDOWN: Line protocol on
Interface AT
M0/0, changed state to down
*Sep 2 19:40:03.080 MET-DST: DSL(ATM0/0): 4: Modem state = 0x8
*Sep 2 19:40:05.580 MET-DST: DSL(ATM0/0): 5: Modem state = 0x8
*Sep 2 19:40:08.080 MET-DST: DSL(ATM0/0): 6: Modem state = 0x10
*Sep 2 19:40:10.580 MET-DST: DSL(ATM0/0): 7: Modem state = 0x10
*Sep 2 19:40:13.080 MET-DST: DSL(ATM0/0): 8: Modem state = 0x10
*Sep 2 19:40:14.392 MET-DST: DSL: Received response: 0x24
*Sep 2 19:40:14.392 MET-DST: DSL: Showtime!
*Sep 2 19:40:14.392 MET-DST: DSL(ATM0/0): Sent command 0x11
*Sep 2 19:40:14.396 MET-DST: DSL: Received response: 0x61
*Sep 2 19:40:14.396 MET-DST: DSL: Read firmware revision 0x1A04
*Sep 2 19:40:14.396 MET-DST: DSL(ATM0/0): Sent command 0x31
*Sep 2 19:40:14.404 MET-DST: DSL: Received response: 0x12
*Sep 2 19:40:14.404 MET-DST: DSL(ATM0/0): operation mode 0x0002
*Sep 2 19:40:14.404 MET-DST: DSL(ATM0/0): Sent command 0x33
*Sep 2 19:40:14.408 MET-DST: DSL: Received response: 0x16
*Sep 2 19:40:14.408 MET-DST: DSL(ATM0/0): Far End ITU Country Code
0x00
*Sep 2 19:40:14.408 MET-DST: DSL: Far End ITU Vendor ID
*Sep 2 19:40:14.408 MET-DST: DSL: Far End ITU Vendor ID Specific
0x0000
*Sep 2 19:40:14.408 MET-DST: DSL: Far End ITU Vendor STD Number 0x0001
*Sep 2 19:40:14.408 MET-DST: DSL(ATM0/0): Sent command 0x32
*Sep 2 19:40:14.412 MET-DST: DSL: Received response: 0x14
*Sep 2 19:40:14.412 MET-DST: DSL(ATM0/0): Near End ITU Country Code
0x00
*Sep 2 19:40:14.412 MET-DST: DSL: Near End ITU Vendor ID ALCB
*Sep 2 19:40:14.412 MET-DST: DSL: Near End ITU Vendor ID Specific
0x0000
*Sep 2 19:40:14.416 MET-DST: DSL: Near End ITU Vendor STD Number
0x0001
*Sep 2 19:40:14.416 MET-DST: ATM0/0 dslsar_MatchSARTxToLineSpeed():
usbw 864, c
lkPerCell 17337 prev_clkPerCell 17337
*Sep 2 19:40:14.416 MET-DST: ATM0/0 dslsar_update_us_bandwidth():
upstream bw 864 Kbps
*Sep 2 19:40:14.416 MET-DST: DSL: SM: [DMTDSL_DO_OPEN ->
DMTDSL_SHOWTIME]
*Sep 2 19:40:19.440 MET-DST: DSL: Defect: LCDi: retraining
*Sep 2 19:40:19.956 MET-DST: dslsar_periodic: ENABLING DSLSAR

*Sep 2 19:40:21.668 MET-DST: dslsar enable ATM0/0

*Sep 2 19:40:21.668 MET-DST: ATM0/0: dslsar_bringup_interface:
Interface and at
m_db flags are UP
*Sep 2 19:40:21.952 MET-DST: DSL: SM: [DMTDSL_SHOWTIME ->
DMTDSL_RE_OPEN]
*Sep 2 19:40:21.956 MET-DST: DSL: Send ADSL_CLOSE command.
*Sep 2 19:40:21.956 MET-DST: DSL(ATM0/0): Sent command 0x4
*Sep 2 19:40:22.400 MET-DST: ATM0/0 check_lockup: scc = 0,
output_qcount = 0, h
ead:(s)1, 1,
addr = (s)0x0, 0x0, count (s)0, 0
*Sep 2 19:40:22.400 MET-DST: ATM0/0 check_lockup: scc = 1,
output_qcount = 0, h
ead:(s)49, 74,
addr = (s)0x64D966F0, 0x0, count (s)545, 567
*Sep 2 19:40:22.480 MET-DST: DSL: Received response: 0x25
*Sep 2 19:40:22.480 MET-DST: DSL: Connection closed
*Sep 2 19:40:22.488 MET-DST: DSL: SM: [DMTDSL_RE_OPEN ->
DMTDSL_DO_OPEN]
*Sep 2 19:40:22.488 MET-DST: DSL: Send ADSL_OPEN command.
*Sep 2 19:40:22.492 MET-DST: DSL(ATM0/0): Using subfunction 0x15
*Sep 2 19:40:22.492 MET-DST: LOCAL:Max noise margin for power cutoff
31
*Sep 2 19:40:22.492 MET-DST: DSL(ATM0/0): Sent command 0x3
*Sep 2 19:40:23.668 MET-DST: %LINK-3-UPDOWN: Interface ATM0/0, changed
state to
up
*Sep 2 19:40:23.668 MET-DST: dslsar_atm_lineaction(ATM0/0): state=4
*Sep 2 19:40:24.668 MET-DST: %LINEPROTO-5-UPDOWN: Line protocol on
Interface AT
M0/0, changed state to up
*Sep 2 19:40:24.992 MET-DST: DSL(ATM0/0): 1: Modem state = 0x8
*Sep 2 19:40:27.492 MET-DST: DSL(ATM0/0): 2: Modem state = 0x8
*Sep 2 19:40:29.956 MET-DST: dslsar disable ATM0/0

*Sep 2 19:40:29.992 MET-DST: DSL(ATM0/0): 3: Modem state = 0x8
*Sep 2 19:40:31.956 MET-DST: %LINK-3-UPDOWN: Interface ATM0/0, changed
state to
down
*Sep 2 19:40:31.956 MET-DST: dslsar_atm_lineaction(ATM0/0): state=0
*Sep 2 19:40:32.492 MET-DST: DSL(ATM0/0): 4: Modem state = 0x8
*Sep 2 19:40:32.956 MET-DST: %LINEPROTO-5-UPDOWN: Line protocol on
Interface AT
M0/0, changed state to down
*Sep 2 19:40:34.991 MET-DST: DSL(ATM0/0): 5: Modem state = 0x8
*Sep 2 19:40:36.119 MET-DST: ATM0/0 dslsar_1a_shutdown: state=6
*Sep 2 19:40:36.119 MET-DST: dslsar disable ATM0/0

*Sep 2 19:40:36.119 MET-DST: DSL: SET: [DMTDSL_DO_OPEN -> DMTDSL_STOP]
*Sep 2 19:40:36.123 MET-DST: Resetting ATM0/0
*Sep 2 19:40:37.491 MET-DST: DSL: SM: [DMTDSL_DO_OPEN -> DMTDSL_STOP]
*Sep 2 19:40:38.119 MET-DST: %LINK-5-CHANGED: Interface ATM0/0,
changed state t
o administratively down
*Sep 2 19:40:38.119 MET-DST: dslsar_atm_lineaction(ATM0/0): state=6
*Sep 2 19:40:44.491 MET-DST: DSL(ATM0/0): Sent command 0x4
*Sep 2 19:40:44.491 MET-DST: DSL: Received response: 0x24
*Sep 2 19:40:44.491 MET-DST: DSL: Unexpected response 0x24
*Sep 2 19:40:44.991 MET-DST: DSL(ATM0/0): Sent command 0x4
*Sep 2 19:40:45.011 MET-DST: DSL: Received response: 0x25
*Sep 2 19:40:45.011 MET-DST: DSL(ATM0/0): Connection closed

Alni

30/12/2005 à 02:01

Bonjour,

JustMe a exposé le 29/12/2005 :

SkyFoxXP a émis l'idée suivante :
Pour le 2+ je comprend c'est une autre techno, mais pour l'ADSL max :
c'est de la techno ADSL1 de base, non ? le nom de "max" est juste
"marketing"

Quelle est la limite de vitesse officiellement supportee par le WIC-1ADSL
?

Normalement, il supporte le 8800K / 880K.

Bon je suis passe en 12.4-3b avec la feature ADSL

Cisco 827. Suis en ADSL Max, pas eu ces problèmes.
Par contre je vois que ton DSLAM n'est pas "Alcatel", alors que c'est
le cas du mien.

Avec toutes les versions 12.2 12.3 et 12.4 que j'ai essayées, j'ai
toujours eu la même synchro (7616 cause DSLAM Alcatel je suppose):
-----------------------------------------------------------
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.1 (G.DMT)
ITU STD NUM: 0x01 0x01
Vendor ID: 'ALCB' 'ALCB'
Vendor Specific: 0x0000 0x0000
Vendor Country: 0x00 0x0F
Capacity Used: 88% 97%
Noise Margin: 5.0 dB 8.0 dB
Output Power: 20.0 dBm 12.0 dBm
Attenuation: 26.0 dB 16.0 dB
Defect Status: None None
Last Fail Code: None
Selftest Result: 0x00
Subfunction: 0x02
Interrupts: 646 (1 spurious)
Activations: 1
Init FW: embedded
Operartion FW: embedded
SW Version: 3.9.19
FW Version: 0x1A04

Interleave Fast Interleave Fast
Speed (kbps): 7616 0 1024 0
Reed-Solomon EC: 64829 0 25282 0
CRC Errors: 0 0 2 0
Header Errors: 0 0 2 0
Bit Errors: 0 0
BER Valid sec: 0 0
BER Invalid sec: 0 0

LOM Monitoring : Disabled

DMT Bits Per Bin
00: 0 0 0 0 0 0 0 A B C C E E E E E
10: E E E E E E E E E D D D C C 0 0
20: 0 0 0 0 0 0 8 8 9 9 A A B B B B
30: B C C C C C A B C C C C C C C B
40: A 2 C C C C B C C C C C C C C C
50: C B C C C C C B C C C C C C C B
60: C C C C C C C C B B C B B C C B
70: B C C B B B B B C C C B B B B A
80: A A A A A A A A A A A A A A A A
90: A A A A A A A A A A A A A A A A
A0: A A A A A A A A A A A A A A A A
B0: A A A A A A A A A A A A A A A A
C0: A A A A A A A 9 8 9 8 8 8 8 8 8
D0: 8 8 8 8 8 9 9 9 9 9 9 9 9 9 9 9
E0: 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 8
F0: 8 8 8 8 8 6 6 4 4 3 0 2 0 0 0 0
----------------------------------------------
show run :
interface ATM0
no ip address
atm vc-per-vp 64
no atm ilmi-keepalive
dsl operating-mode auto
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
interface Dialer1
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname fti/xxxxxxx
ppp chap password 7 xxxxxxx
ppp pap sent-username fti/xxxxxxx password 7 xxxxxxx
hold-queue 224 in

--
Alni

Bonjour,

JustMe a exposé le 29/12/2005 :

SkyFoxXP a émis l'idée suivante :

Pour le 2+ je comprend c'est une autre techno, mais pour l'ADSL max :
c'est de la techno ADSL1 de base, non ? le nom de "max" est juste
"marketing"

Quelle est la limite de vitesse officiellement supportee par le WIC-1ADSL
?

Normalement, il supporte le 8800K / 880K.

Bon je suis passe en 12.4-3b avec la feature ADSL

Cisco 827. Suis en ADSL Max, pas eu ces problèmes.
Par contre je vois que ton DSLAM n'est pas "Alcatel", alors que c'est
le cas du mien.

Avec toutes les versions 12.2 12.3 et 12.4 que j'ai essayées, j'ai
toujours eu la même synchro (7616 cause DSLAM Alcatel je suppose):
-----------------------------------------------------------
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.1 (G.DMT)
ITU STD NUM: 0x01 0x01
Vendor ID: 'ALCB' 'ALCB'
Vendor Specific: 0x0000 0x0000
Vendor Country: 0x00 0x0F
Capacity Used: 88% 97%
Noise Margin: 5.0 dB 8.0 dB
Output Power: 20.0 dBm 12.0 dBm
Attenuation: 26.0 dB 16.0 dB
Defect Status: None None
Last Fail Code: None
Selftest Result: 0x00
Subfunction: 0x02
Interrupts: 646 (1 spurious)
Activations: 1
Init FW: embedded
Operartion FW: embedded
SW Version: 3.9.19
FW Version: 0x1A04

Interleave Fast Interleave Fast
Speed (kbps): 7616 0 1024 0
Reed-Solomon EC: 64829 0 25282 0
CRC Errors: 0 0 2 0
Header Errors: 0 0 2 0
Bit Errors: 0 0
BER Valid sec: 0 0
BER Invalid sec: 0 0

LOM Monitoring : Disabled

DMT Bits Per Bin
00: 0 0 0 0 0 0 0 A B C C E E E E E
10: E E E E E E E E E D D D C C 0 0
20: 0 0 0 0 0 0 8 8 9 9 A A B B B B
30: B C C C C C A B C C C C C C C B
40: A 2 C C C C B C C C C C C C C C
50: C B C C C C C B C C C C C C C B
60: C C C C C C C C B B C B B C C B
70: B C C B B B B B C C C B B B B A
80: A A A A A A A A A A A A A A A A
90: A A A A A A A A A A A A A A A A
A0: A A A A A A A A A A A A A A A A
B0: A A A A A A A A A A A A A A A A
C0: A A A A A A A 9 8 9 8 8 8 8 8 8
D0: 8 8 8 8 8 9 9 9 9 9 9 9 9 9 9 9
E0: 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 8
F0: 8 8 8 8 8 6 6 4 4 3 0 2 0 0 0 0
----------------------------------------------
show run :
interface ATM0
no ip address
atm vc-per-vp 64
no atm ilmi-keepalive
dsl operating-mode auto
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
interface Dialer1
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname fti/xxxxxxx
ppp chap password 7 xxxxxxx
ppp pap sent-username fti/xxxxxxx password 7 xxxxxxx
hold-queue 224 in

--
Alni

Vous avez filtré cet utilisateur ! Consultez son message

Bonjour,

JustMe a exposé le 29/12/2005 :

SkyFoxXP a émis l'idée suivante :
Pour le 2+ je comprend c'est une autre techno, mais pour l'ADSL max :
c'est de la techno ADSL1 de base, non ? le nom de "max" est juste
"marketing"

Quelle est la limite de vitesse officiellement supportee par le WIC-1ADSL
?

Normalement, il supporte le 8800K / 880K.

Bon je suis passe en 12.4-3b avec la feature ADSL

Cisco 827. Suis en ADSL Max, pas eu ces problèmes.
Par contre je vois que ton DSLAM n'est pas "Alcatel", alors que c'est
le cas du mien.

Avec toutes les versions 12.2 12.3 et 12.4 que j'ai essayées, j'ai
toujours eu la même synchro (7616 cause DSLAM Alcatel je suppose):
-----------------------------------------------------------
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.1 (G.DMT)
ITU STD NUM: 0x01 0x01
Vendor ID: 'ALCB' 'ALCB'
Vendor Specific: 0x0000 0x0000
Vendor Country: 0x00 0x0F
Capacity Used: 88% 97%
Noise Margin: 5.0 dB 8.0 dB
Output Power: 20.0 dBm 12.0 dBm
Attenuation: 26.0 dB 16.0 dB
Defect Status: None None
Last Fail Code: None
Selftest Result: 0x00
Subfunction: 0x02
Interrupts: 646 (1 spurious)
Activations: 1
Init FW: embedded
Operartion FW: embedded
SW Version: 3.9.19
FW Version: 0x1A04

Interleave Fast Interleave Fast
Speed (kbps): 7616 0 1024 0
Reed-Solomon EC: 64829 0 25282 0
CRC Errors: 0 0 2 0
Header Errors: 0 0 2 0
Bit Errors: 0 0
BER Valid sec: 0 0
BER Invalid sec: 0 0

LOM Monitoring : Disabled

DMT Bits Per Bin
00: 0 0 0 0 0 0 0 A B C C E E E E E
10: E E E E E E E E E D D D C C 0 0
20: 0 0 0 0 0 0 8 8 9 9 A A B B B B
30: B C C C C C A B C C C C C C C B
40: A 2 C C C C B C C C C C C C C C
50: C B C C C C C B C C C C C C C B
60: C C C C C C C C B B C B B C C B
70: B C C B B B B B C C C B B B B A
80: A A A A A A A A A A A A A A A A
90: A A A A A A A A A A A A A A A A
A0: A A A A A A A A A A A A A A A A
B0: A A A A A A A A A A A A A A A A
C0: A A A A A A A 9 8 9 8 8 8 8 8 8
D0: 8 8 8 8 8 9 9 9 9 9 9 9 9 9 9 9
E0: 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 8
F0: 8 8 8 8 8 6 6 4 4 3 0 2 0 0 0 0
----------------------------------------------
show run :
interface ATM0
no ip address
atm vc-per-vp 64
no atm ilmi-keepalive
dsl operating-mode auto
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
interface Dialer1
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname fti/xxxxxxx
ppp chap password 7 xxxxxxx
ppp pap sent-username fti/xxxxxxx password 7 xxxxxxx
hold-queue 224 in

--
Alni

ADSL Max et Wic ADSL Cisco

8 réponses

Veuillez sélectionner un problème