J'ai installé le paquet lm-sensors sous debian sid avec apt.
Jai recompilé mon noyau pour le support des différents modules, sauf
pour smbus-arp, que je n'ai pas trouvé mais appremment, celui-là n'est
pas obligatoire non?
Voila ce qu'ils ont rajouté dans mon /etc/modules:
# Generated by sensors-detect on Fri Jan 27 15:14:21 2006
# I2C adapter drivers
i2c-i801
# I2C chip drivers
# Warning: the required module asb100 is not currently installed on your
system.
# For status of 2.6 kernel ports see
http://secure.netroedge.com/~lm78/supported.html
# If driver is built-in to the kernel, or unavailable, comment out the
following line.
asb100
# Warning: the required module smbus-arp is not currently installed on
your system.
# For status of 2.6 kernel ports see
http://secure.netroedge.com/~lm78/supported.html
# If driver is built-in to the kernel, or unavailable, comment out the
following line.
#smbus-arp
Donc, j'ai décoché smbus-arp.
Quand je tape sensors, voila ce qu'il m'affiche:
sb100-i2c-0-2d
Adapter: SMBus I801 adapter at e800
VCore 1: +1.71 V (min = +1.66 V, max = +1.84 V)
+3.3V: +3.34 V (min = +3.14 V, max = +3.47 V)
+5V: +5.05 V (min = +4.76 V, max = +5.24 V)
+12V: +11.43 V (min = +10.82 V, max = +13.19 V)
-12V (reserved):
-11.94 V (min = -0.00 V, max = -0.00 V)
-5V (reserved):
-5.01 V (min = -0.00 V, max = -0.00 V)
CPU Fan: 3629 RPM (min = 1997 RPM, div = 4)
Chassis Fan:
0 RPM (min = 3994 RPM, div = 2)
Power Fan: 0 RPM (min = 3994 RPM, div = 2)
M/B Temp: +42°C (high = +45°C, hyst = +40°C)
CPU Temp (Intel):
+40°C (high = +60°C, hyst = +50°C)
Power Temp:
+124°C (high = +45°C, hyst = +40°C)
CPU Temp (AMD):
-41°C (high = +60°C, hyst = +50°C)
vid: +1.750 V (VRM Version 9.0)
alarms:
Ca a l'air correcte?
Sinon, un autre truc, l'ordi emet des sons une fois par minute à peu
près, depuis le chargement de ces modules.
Y'a moyen de stopper cela?
Merci
A+
--
Pensez à lire la FAQ de la liste avant de poser une question :
http://wiki.debian.net/?DebianFrench
Pensez à rajouter le mot ``spam'' dans vos champs "From" et "Reply-To:"
To UNSUBSCRIBE, email to debian-user-french-REQUEST@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmaster@lists.debian.org
Cette action est irreversible, confirmez la suppression du commentaire ?
Signaler le commentaire
Veuillez sélectionner un problème
Nudité
Violence
Harcèlement
Fraude
Vente illégale
Discours haineux
Terrorisme
Autre
mess-mate
Thierry B wrote: | Bonjour, | | J'ai installé le paquet lm-sensors sous debian sid avec apt. | | Jai recompilé mon noyau pour le support des différents modules, sau f | pour smbus-arp, que je n'ai pas trouvé mais appremment, celui-là n' est | pas obligatoire non? | | Voila ce qu'ils ont rajouté dans mon /etc/modules: | | # Generated by sensors-detect on Fri Jan 27 15:14:21 2006 | # I2C adapter drivers | i2c-i801 | # I2C chip drivers | # Warning: the required module asb100 is not currently installed on you r | system. | # For status of 2.6 kernel ports see | http://secure.netroedge.com/~lm78/supported.html | # If driver is built-in to the kernel, or unavailable, comment out the | following line. | asb100 | # Warning: the required module smbus-arp is not currently installed on | your system. | # For status of 2.6 kernel ports see | http://secure.netroedge.com/~lm78/supported.html | # If driver is built-in to the kernel, or unavailable, comment out the | following line. | #smbus-arp | | Donc, j'ai décoché smbus-arp. | | Quand je tape sensors, voila ce qu'il m'affiche: | | sb100-i2c-0-2d | Adapter: SMBus I801 adapter at e800 | VCore 1: +1.71 V (min = +1.66 V, max = +1.84 V) | +3.3V: +3.34 V (min = +3.14 V, max = +3.47 V) | +5V: +5.05 V (min = +4.76 V, max = +5.24 V) | +12V: +11.43 V (min = +10.82 V, max = +13.19 V) | -12V (reserved): | -11.94 V (min = -0.00 V, max = -0.00 V) | -5V (reserved): | -5.01 V (min = -0.00 V, max = -0.00 V) | CPU Fan: 3629 RPM (min = 1997 RPM, div = 4) | Chassis Fan: | 0 RPM (min = 3994 RPM, div = 2) | Power Fan: 0 RPM (min = 3994 RPM, div = 2) | M/B Temp: +42°C (high = +45°C, hyst = +40°C) | CPU Temp (Intel): | +40°C (high = +60°C, hyst = +50°C) | Power Temp: | +124°C (high = +45°C, hyst = +40°C) | CPU Temp (AMD): | -41°C (high = +60°C, hyst = +50°C) | vid: +1.750 V (VRM Version 9.0) | alarms: | | puisque j'ai l'asb100 : asb100-i2c-0-2d Adapter: SMBus I801 adapter at e800 VCore 1: +1.57 V (min = +1.42 V, max = +1.57 V) ALARM +3.3V: +3.38 V (min = +3.14 V, max = +3.47 V) +5V: +5.08 V (min = +4.76 V, max = +5.24 V) +12V: +11.67 V (min = +10.82 V, max = +13.19 V) -12V (reserved): -12.13 V (min = -0.00 V, max = -0.00 V) -5V (reserved): -5.09 V (min = -0.00 V, max = -0.00 V) CPU Fan: 2220 RPM (min = 1997 RPM, div = 4) fan2: 0 RPM (min = 3994 RPM, div = 2) Power Fan: 0 RPM (min = 3994 RPM, div = 2) M/B Temp: +26°C (high = +45°C, hyst = +40°C) vid: +1.500 V (VRM Version 9.0)
mess-mate --
Big book, big bore. -- Callimachus
Thierry B <debian@thierry.eu.org> wrote:
| Bonjour,
|
| J'ai installé le paquet lm-sensors sous debian sid avec apt.
|
| Jai recompilé mon noyau pour le support des différents modules, sau f
| pour smbus-arp, que je n'ai pas trouvé mais appremment, celui-là n' est
| pas obligatoire non?
|
| Voila ce qu'ils ont rajouté dans mon /etc/modules:
|
| # Generated by sensors-detect on Fri Jan 27 15:14:21 2006
| # I2C adapter drivers
| i2c-i801
| # I2C chip drivers
| # Warning: the required module asb100 is not currently installed on you r
| system.
| # For status of 2.6 kernel ports see
| http://secure.netroedge.com/~lm78/supported.html
| # If driver is built-in to the kernel, or unavailable, comment out the
| following line.
| asb100
| # Warning: the required module smbus-arp is not currently installed on
| your system.
| # For status of 2.6 kernel ports see
| http://secure.netroedge.com/~lm78/supported.html
| # If driver is built-in to the kernel, or unavailable, comment out the
| following line.
| #smbus-arp
|
| Donc, j'ai décoché smbus-arp.
|
| Quand je tape sensors, voila ce qu'il m'affiche:
|
| sb100-i2c-0-2d
| Adapter: SMBus I801 adapter at e800
| VCore 1: +1.71 V (min = +1.66 V, max = +1.84 V)
| +3.3V: +3.34 V (min = +3.14 V, max = +3.47 V)
| +5V: +5.05 V (min = +4.76 V, max = +5.24 V)
| +12V: +11.43 V (min = +10.82 V, max = +13.19 V)
| -12V (reserved):
| -11.94 V (min = -0.00 V, max = -0.00 V)
| -5V (reserved):
| -5.01 V (min = -0.00 V, max = -0.00 V)
| CPU Fan: 3629 RPM (min = 1997 RPM, div = 4)
| Chassis Fan:
| 0 RPM (min = 3994 RPM, div = 2)
| Power Fan: 0 RPM (min = 3994 RPM, div = 2)
| M/B Temp: +42°C (high = +45°C, hyst = +40°C)
| CPU Temp (Intel):
| +40°C (high = +60°C, hyst = +50°C)
| Power Temp:
| +124°C (high = +45°C, hyst = +40°C)
| CPU Temp (AMD):
| -41°C (high = +60°C, hyst = +50°C)
| vid: +1.750 V (VRM Version 9.0)
| alarms:
|
|
puisque j'ai l'asb100 :
asb100-i2c-0-2d
Adapter: SMBus I801 adapter at e800
VCore 1: +1.57 V (min = +1.42 V, max = +1.57 V) ALARM
+3.3V: +3.38 V (min = +3.14 V, max = +3.47 V)
+5V: +5.08 V (min = +4.76 V, max = +5.24 V)
+12V: +11.67 V (min = +10.82 V, max = +13.19 V)
-12V (reserved):
-12.13 V (min = -0.00 V, max = -0.00 V)
-5V (reserved):
-5.09 V (min = -0.00 V, max = -0.00 V)
CPU Fan: 2220 RPM (min = 1997 RPM, div = 4)
fan2: 0 RPM (min = 3994 RPM, div = 2)
Power Fan: 0 RPM (min = 3994 RPM, div = 2)
M/B Temp: +26°C (high = +45°C, hyst = +40°C)
vid: +1.500 V (VRM Version 9.0)
Thierry B wrote: | Bonjour, | | J'ai installé le paquet lm-sensors sous debian sid avec apt. | | Jai recompilé mon noyau pour le support des différents modules, sau f | pour smbus-arp, que je n'ai pas trouvé mais appremment, celui-là n' est | pas obligatoire non? | | Voila ce qu'ils ont rajouté dans mon /etc/modules: | | # Generated by sensors-detect on Fri Jan 27 15:14:21 2006 | # I2C adapter drivers | i2c-i801 | # I2C chip drivers | # Warning: the required module asb100 is not currently installed on you r | system. | # For status of 2.6 kernel ports see | http://secure.netroedge.com/~lm78/supported.html | # If driver is built-in to the kernel, or unavailable, comment out the | following line. | asb100 | # Warning: the required module smbus-arp is not currently installed on | your system. | # For status of 2.6 kernel ports see | http://secure.netroedge.com/~lm78/supported.html | # If driver is built-in to the kernel, or unavailable, comment out the | following line. | #smbus-arp | | Donc, j'ai décoché smbus-arp. | | Quand je tape sensors, voila ce qu'il m'affiche: | | sb100-i2c-0-2d | Adapter: SMBus I801 adapter at e800 | VCore 1: +1.71 V (min = +1.66 V, max = +1.84 V) | +3.3V: +3.34 V (min = +3.14 V, max = +3.47 V) | +5V: +5.05 V (min = +4.76 V, max = +5.24 V) | +12V: +11.43 V (min = +10.82 V, max = +13.19 V) | -12V (reserved): | -11.94 V (min = -0.00 V, max = -0.00 V) | -5V (reserved): | -5.01 V (min = -0.00 V, max = -0.00 V) | CPU Fan: 3629 RPM (min = 1997 RPM, div = 4) | Chassis Fan: | 0 RPM (min = 3994 RPM, div = 2) | Power Fan: 0 RPM (min = 3994 RPM, div = 2) | M/B Temp: +42°C (high = +45°C, hyst = +40°C) | CPU Temp (Intel): | +40°C (high = +60°C, hyst = +50°C) | Power Temp: | +124°C (high = +45°C, hyst = +40°C) | CPU Temp (AMD): | -41°C (high = +60°C, hyst = +50°C) | vid: +1.750 V (VRM Version 9.0) | alarms: | | puisque j'ai l'asb100 : asb100-i2c-0-2d Adapter: SMBus I801 adapter at e800 VCore 1: +1.57 V (min = +1.42 V, max = +1.57 V) ALARM +3.3V: +3.38 V (min = +3.14 V, max = +3.47 V) +5V: +5.08 V (min = +4.76 V, max = +5.24 V) +12V: +11.67 V (min = +10.82 V, max = +13.19 V) -12V (reserved): -12.13 V (min = -0.00 V, max = -0.00 V) -5V (reserved): -5.09 V (min = -0.00 V, max = -0.00 V) CPU Fan: 2220 RPM (min = 1997 RPM, div = 4) fan2: 0 RPM (min = 3994 RPM, div = 2) Power Fan: 0 RPM (min = 3994 RPM, div = 2) M/B Temp: +26°C (high = +45°C, hyst = +40°C) vid: +1.500 V (VRM Version 9.0)
