Pb carte réseau (portable)

manu

15/03/2006 à 19:11

Le Wed, 15 Mar 2006 17:23:07 +0100, =?ISO-8859-15?Q?Sébastien.kirche?= a
écrit :

Typo sur la seconde commande : c'est en fait dhcpcd eth0.
Ce sont deux commande qui permettent de demander un bail dhcp sur
l'interface réseau. Je pensais que tu pouvais ne pas avoir de client
dhcp installé, or tu as configuré ton interface pour demander une
adresse par dhcp.
A la réflexion, c'est autement improbable que tu n'aies pas de client
dhcp.

sudo dhcpcd eth0
sudo : dhcpcd : command no found !!!

pourtant il me semble avoir les paquetages nécessaires au DHCP :
sur Ubuntu Breezy (5.10)
dhcp3-client-3.0.2-1ubuntu6
dhcp3-common-3.0.2-1ubuntu6

manu

Sébastien Kirche

15/03/2006 à 19:18

Le 15 March 2006 à 19:11, manu s'est exprimé ainsi :

sudo dhcpcd eth0
sudo : dhcpcd : command no found !!!

pourtant il me semble avoir les paquetages nécessaires au DHCP :
sur Ubuntu Breezy (5.10)
dhcp3-client-3.0.2-1ubuntu6
dhcp3-common-3.0.2-1ubuntu6

Oui cf la remarque de Pascal, il existe d'autres clients dhcp. Le
commandes que j'ai cité ne sont que celles que j'utilise le plus.
Du coup tu dois avoir dhclient plutôt.

--
Sébastien Kirche

manu

15/03/2006 à 20:42

Le Wed, 15 Mar 2006 19:18:58 +0100, Sébastien Kirche a écrit :

Oui cf la remarque de Pascal, il existe d'autres clients dhcp. Le
commandes que j'ai cité ne sont que celles que j'utilise le plus.
Du coup tu dois avoir dhclient plutôt.

OK j'ai pigé

donc chez moi ça donne ça :
sudo dhclient eth0

sit0: unknown hardware address type 776
sit0: unknown hardware address type 776
Listening on LPF/eth0/00:a0:d1:28:e3:14
Sending on LPF/eth0/00:a0:d1:28:e3:14
Sending on Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
DHCPOFFER from 192.168.10.254
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPACK from 192.168.10.254
bound to 192.168.10.5 -- renewal in 337639 seconds.

manu

Sébastien.kirche

15/03/2006 à 21:04

manu a présenté l'énoncé suivant :

DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
DHCPOFFER from 192.168.10.254
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPACK from 192.168.10.254
bound to 192.168.10.5 -- renewal in 337639 seconds.

Donc, automatiquement ton interface réseau ne se configure pas en dhcp,
par contre lorsque tu appelles manuellement le serveur tu obtiens le
bail.

Vérifies bien que tu n'as pas une erreur dans ton
/etc/network/interfaces

Sinon ça pourrait venir d'un problème de timing au démarrage, genre le
montage des interfaces réseau qui se ferait avant le chargement du
module de ta carte ? Vérifie dans dmesg dans quel ordre ça se passe.

HTH.

--
Sébastien Kirche

manu

16/03/2006 à 14:48

Le Wed, 15 Mar 2006 21:04:15 +0100, =?ISO-8859-15?Q?Sébastien.kirche?= a
écrit :

Sinon ça pourrait venir d'un problème de timing au démarrage, genre le
montage des interfaces réseau qui se ferait avant le chargement du
module de ta carte ? Vérifie dans dmesg dans quel ordre ça se passe.

Apparemment le module (sk98lin) est chargé avant la reconnaissance de la
carte réseau :

[ 39.322935] sk98lin: Network Device Driver v8.23.1.3
[ 39.322936] (C)Copyright 1999-2005 Marvell(R).

[ 39.393830] eth0: Marvell Yukon 88E8036 Fast Ethernet Controller
[ 39.393834] PrefPort:A RlmtMode:Check Link State

... !

mais peut-être y a-t-il d'autres choses concernant le réseau que je ne
sais décripter dans dmesg (ci-dessous dans son entier)

[ 10.025070] Allocate Port Service[pcie02]
[ 10.025114] PCI: Found IRQ 11 for device 0000:00:1c.1
[ 10.025117] PCI: Sharing IRQ 11 with 0000:00:01.0
[ 10.025127] PCI: Sharing IRQ 11 with 0000:00:1d.3
[ 10.025137] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 10.025141] PCI: Sharing IRQ 11 with 0000:02:00.0
[ 10.025145] PCI: Sharing IRQ 11 with 0000:06:04.0
[ 10.025156] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 10.025205] assign_interrupt_mode Found MSI capability
[ 10.025207] Allocate Port Service[pcie00]
[ 10.025229] Allocate Port Service[pcie02]
[ 10.025254] isapnp: Scanning for PnP cards...
[ 10.378529] isapnp: No Plug & Play device found
[ 10.392395] PNP: No PS/2 controller found. Probing ports directly.
[ 10.395824] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 10.397999] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 10.398335] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 10.398601] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 10.398918] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 10.399185] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 10.399188] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
[ 10.400603] PCI: Found IRQ 5 for device 0000:00:1e.3
[ 10.400634] PCI: Sharing IRQ 5 with 0000:06:06.3
[ 10.400646] io scheduler noop registered
[ 10.400655] io scheduler anticipatory registered
[ 10.400659] io scheduler deadline registered
[ 10.400666] io scheduler cfq registered
[ 10.400936] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 10.400990] NET: Registered protocol family 2
[ 10.410339] IP: routing cache hash table of 8192 buckets, 64Kbytes
[ 10.410490] TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
[ 10.412801] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[ 10.413132] TCP: Hash tables configured (established 262144 bind 65536)
[ 10.413227] NET: Registered protocol family 8
[ 10.413230] NET: Registered protocol family 20
[ 10.413439] Freeing unused kernel memory: 168k freed
[ 10.419773] input: AT Translated Set 2 keyboard on isa0060/serio0
[ 10.425378] vga16fb: initializing
[ 10.425381] vga16fb: mapped to 0xc00a0000
[ 10.545395] Console: switching to colour frame buffer device 80x30
[ 10.545400] fb0: VGA16 VGA frame buffer device
[ 11.684969] Capability LSM initialized
[ 11.693021] NET: Registered protocol family 1
[ 11.705800] SCSI subsystem initialized
[ 11.706530] libata version 1.11 loaded.
[ 11.707262] ahci version 1.00
[ 11.707280] PCI: Found IRQ 11 for device 0000:00:1f.2
[ 11.707289] PCI: Sharing IRQ 11 with 0000:00:1d.1
[ 11.707323] ahci: probe of 0000:00:1f.2 failed with error -12
[ 11.708525] ata_piix version 1.03
[ 11.708559] PCI: Found IRQ 11 for device 0000:00:1f.2
[ 11.708568] PCI: Sharing IRQ 11 with 0000:00:1d.1
[ 11.708598] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 11.708625] ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x1100 irq 14
[ 11.862714] ata1: dev 0 cfg 49:2f00 82:746b 83:7d09 84:6023 85:7468 86:3c09 87:6023 88:203f
[ 11.862717] ata1: dev 0 ATA, max UDMA/100, 156301488 sectors: lba48
[ 11.862823] ata1: dev 0 configured for UDMA/100
[ 11.862825] scsi0 : ata_piix
[ 11.862906] Vendor: ATA Model: TOSHIBA MK8032GS Rev: AS11
[ 11.862913] Type: Direct-Access ANSI SCSI revision: 05
[ 11.863336] ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x1108 irq 15
[ 12.170330] ata2: dev 0 cfg 49:0f00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 88:0407
[ 12.170333] ata2: dev 0 ATAPI, max UDMA/33
[ 12.170335] ata2(0): applying bridge limits
[ 12.170753] ata2: dev 0 configured for UDMA/33
[ 12.170754] scsi1 : ata_piix
[ 12.172584] Vendor: MATSHITA Model: DVD-RAM UJ-841S Rev: 1.00
[ 12.172591] Type: CD-ROM ANSI SCSI revision: 05
[ 12.183301] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 12.183309] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 12.183635] ide0: I/O resource 0x1F0-0x1F7 not free.
[ 12.183638] ide0: ports already in use, skipping probe
[ 12.183640] ide1: I/O resource 0x170-0x177 not free.
[ 12.183642] ide1: ports already in use, skipping probe
[ 12.183644] Probing IDE interface ide2...
[ 12.695988] Probing IDE interface ide3...
[ 13.207693] Probing IDE interface ide4...
[ 13.719399] Probing IDE interface ide5...
[ 14.234002] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
[ 14.234010] SCSI device sda: drive cache: write back
[ 14.234063] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
[ 14.234070] SCSI device sda: drive cache: write back
[ 14.234073] /dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 >
[ 14.340502] Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
[ 14.470420] Attempting manual resume
[ 14.482745] swsusp: Suspend partition has wrong signature?
[ 14.515214] usbcore: registered new driver usbfs
[ 14.515237] usbcore: registered new driver hub
[ 14.515889] USB Universal Host Controller Interface driver v2.2
[ 14.515955] PCI: Found IRQ 11 for device 0000:00:1d.0
[ 14.515970] PCI: Sharing IRQ 11 with 0000:00:1d.7
[ 14.515998] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 14.516002] uhci_hcd 0000:00:1d.0: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1
[ 14.578018] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 14.578026] uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001200
[ 14.578115] hub 1-0:1.0: USB hub found
[ 14.578121] hub 1-0:1.0: 2 ports detected
[ 14.580919] PCI: Found IRQ 11 for device 0000:00:1d.1
[ 14.580938] PCI: Sharing IRQ 11 with 0000:00:1f.2
[ 14.580955] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 14.580959] uhci_hcd 0000:00:1d.1: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2
[ 14.642896] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 14.642901] uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001220
[ 14.642980] hub 2-0:1.0: USB hub found
[ 14.642986] hub 2-0:1.0: 2 ports detected
[ 14.645883] PCI: Found IRQ 11 for device 0000:00:1d.2
[ 14.645909] PCI: Sharing IRQ 11 with 0000:06:06.0
[ 14.645916] PCI: Sharing IRQ 11 with 0000:06:06.4
[ 14.645921] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 14.645925] uhci_hcd 0000:00:1d.2: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3
[ 14.707853] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 14.707858] uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001240
[ 14.707938] hub 3-0:1.0: USB hub found
[ 14.707944] hub 3-0:1.0: 2 ports detected
[ 14.710845] PCI: Found IRQ 11 for device 0000:00:1d.3
[ 14.710848] PCI: Sharing IRQ 11 with 0000:00:01.0
[ 14.710853] PCI: Sharing IRQ 11 with 0000:00:1c.1
[ 14.710869] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 14.710873] PCI: Sharing IRQ 11 with 0000:02:00.0
[ 14.710877] PCI: Sharing IRQ 11 with 0000:06:04.0
[ 14.710890] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 14.710894] uhci_hcd 0000:00:1d.3: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4
[ 14.772816] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[ 14.772821] uhci_hcd 0000:00:1d.3: irq 11, io base 0x00001260
[ 14.772901] hub 4-0:1.0: USB hub found
[ 14.772906] hub 4-0:1.0: 2 ports detected
[ 14.801745] PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
[ 14.801754] PCI: Found IRQ 11 for device 0000:00:1d.7
[ 14.801788] PCI: Sharing IRQ 11 with 0000:00:1d.0
[ 14.801824] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 14.801828] ehci_hcd 0000:00:1d.7: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller
[ 14.801843] ehci_hcd 0000:00:1d.7: debug port 1
[ 14.801872] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[ 14.801878] ehci_hcd 0000:00:1d.7: irq 11, io mem 0xf4000000
[ 14.805787] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 14.805795] ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
[ 14.805853] hub 5-0:1.0: USB hub found
[ 14.805859] hub 5-0:1.0: 8 ports detected
[ 17.502640] Attempting manual resume
[ 17.502819] swsusp: Suspend partition has wrong signature?
[ 17.508765] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 17.508768] EXT3-fs: write access will be enabled during recovery.
[ 17.526373] kjournald starting. Commit interval 5 seconds
[ 17.526378] EXT3-fs: recovery complete.
[ 17.526585] EXT3-fs: mounted filesystem with ordered data mode.
[ 18.531564] md: md driver 0.90.1 MAX_MD_DEVS%6, MD_SB_DISKS'
[ 21.336581] Adding 1092380k swap on /dev/sda5. Priority:-1 extents:1
[ 21.597325] EXT3 FS on sda8, internal journal
[ 27.963324] lp: driver loaded but no devices found
[ 27.989217] mice: PS/2 mouse device common for all mice
[ 28.017394] ieee1394: Initialized config rom entry `ip1394'
[ 28.020862] sbp2: $Rev: 1219 $ Ben Collins
[ 28.872470] Synaptics Touchpad, model: 1, fw: 6.2, id: 0xa5a0b1, caps: 0xa04713/0x0
[ 28.872476] synaptics: Toshiba Satellite M40 detected, limiting rate to 40pps.
[ 28.874296] input: SynPS/2 Synaptics TouchPad on isa0060/serio1
[ 29.150802] ts: Compaq touchscreen protocol output
[ 30.589523] device-mapper: 4.4.0-ioctl (2005-01-12) initialised:
[ 36.155775] kjournald starting. Commit interval 5 seconds
[ 36.155998] EXT3 FS on sda6, internal journal
[ 36.156002] EXT3-fs: mounted filesystem with ordered data mode.
[ 36.177895] kjournald starting. Commit interval 5 seconds
[ 36.178171] EXT3 FS on sda7, internal journal
[ 36.178174] EXT3-fs: mounted filesystem with ordered data mode.
[ 36.179333] kjournald starting. Commit interval 5 seconds
[ 36.179796] EXT3 FS on sda9, internal journal
[ 36.179799] EXT3-fs: mounted filesystem with ordered data mode.
[ 37.379031] Linux agpgart interface v0.101 (c) Dave Jones
[ 37.384455] agpgart: Detected an Intel 915GM Chipset.
[ 37.413116] agpgart: AGP aperture is 256M @ 0x0
[ 37.485151] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 37.488474] shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
[ 37.553342] shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
[ 37.618814] shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
[ 37.857151] hw_random: cannot enable RNG, aborting
[ 37.992751] PCI: Found IRQ 10 for device 0000:00:1e.2
[ 37.992758] PCI: Sharing IRQ 10 with 0000:00:1c.0
[ 37.992807] PCI: Setting latency timer of device 0000:00:1e.2 to 64
[ 38.802000] intel8x0_measure_ac97_clock: measured 49510 usecs
[ 38.802003] intel8x0: clocking to 48000
[ 39.322884] PCI: Found IRQ 11 for device 0000:02:00.0
[ 39.322890] PCI: Sharing IRQ 11 with 0000:00:01.0
[ 39.322895] PCI: Sharing IRQ 11 with 0000:00:1c.1
[ 39.322903] PCI: Sharing IRQ 11 with 0000:00:1d.3
[ 39.322915] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 39.322920] PCI: Sharing IRQ 11 with 0000:06:04.0
[ 39.322935] sk98lin: Network Device Driver v8.23.1.3
[ 39.322936] (C)Copyright 1999-2005 Marvell(R).
[ 39.322963] PCI: Found IRQ 11 for device 0000:02:00.0
[ 39.322966] PCI: Sharing IRQ 11 with 0000:00:01.0
[ 39.322970] PCI: Sharing IRQ 11 with 0000:00:1c.1
[ 39.322977] PCI: Sharing IRQ 11 with 0000:00:1d.3
[ 39.322988] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 39.322994] PCI: Sharing IRQ 11 with 0000:06:04.0
[ 39.323007] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 39.393830] eth0: Marvell Yukon 88E8036 Fast Ethernet Controller
[ 39.393834] PrefPort:A RlmtMode:Check Link State
[ 39.455042] ieee80211_crypt: registered algorithm 'NULL'
[ 39.463762] ieee80211: 802.11 data/management/control stack, 1.0.3
[ 39.463766] ieee80211: Copyright (C) 2004-2005 Intel Corporation
[ 39.470580] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.0.6
[ 39.470583] ipw2200: Copyright(c) 2003-2004 Intel Corporation
[ 39.472965] PCI: Found IRQ 11 for device 0000:06:04.0
[ 39.472970] PCI: Sharing IRQ 11 with 0000:00:01.0
[ 39.472975] PCI: Sharing IRQ 11 with 0000:00:1c.1
[ 39.472983] PCI: Sharing IRQ 11 with 0000:00:1d.3
[ 39.472994] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 39.472998] PCI: Sharing IRQ 11 with 0000:02:00.0
[ 39.473039] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[ 40.018423] ipw2200: Radio Frequency Kill Switch is On:
[ 40.018425] Kill switch must be turned off for wireless networking to work.
[ 40.094021] Linux Kernel Card Services
[ 40.094024] options: [pci] [cardbus] [pm]
[ 40.096793] PCI: Found IRQ 11 for device 0000:06:06.0
[ 40.096804] PCI: Sharing IRQ 11 with 0000:00:1d.2
[ 40.096829] PCI: Sharing IRQ 11 with 0000:06:06.4
[ 40.096837] Yenta: CardBus bridge found at 0000:06:06.0 [1179:ff10]
[ 40.096884] Yenta: Enabling burst memory read transactions
[ 40.096889] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 40.096891] Yenta: Routing CardBus interrupts to PCI
[ 40.096897] Yenta TI: socket 0000:06:06.0, mfunc 0x01aa1b22, devctl 0x66
[ 40.317743] Yenta: ISA IRQ mask 0x02d8, PCI irq 11
[ 40.317747] Socket status: 30000006
[ 40.388658] ohci1394: $Rev: 1250 $ Ben Collins
[ 40.388682] PCI: Found IRQ 11 for device 0000:06:06.2
[ 40.439133] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[b0000000-b00007ff] Max Packet=[2048]
[ 41.695450] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00080da0d128e314]
[ 41.812659] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 41.812663] Uniform CD-ROM driver Revision: 3.20
[ 41.813146] Attached scsi CD-ROM sr0 at scsi1, channel 0, id 0, lun 0
[ 41.824884] Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
[ 41.825378] Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 5
[ 42.174616] NET: Registered protocol family 17
[ 110.418325] mtrr: no more MTRRs available
[ 110.418502] mtrr: no more MTRRs available
[ 110.418610] mtrr: no more MTRRs available
[ 113.350807] apm: BIOS not found.
[ 114.159499] cs: IO port probe 0x100-0x4ff: excluding 0x300-0x307 0x310-0x31f 0x370-0x377 0x3f0-0x3f7 0x4d0-0x4d7
[ 114.162259] cs: IO port probe 0xc00-0xcf7: clean.
[ 114.162974] cs: IO port probe 0xa00-0xaff: clean.
[ 115.163952] Bluetooth: Core ver 2.7
[ 115.163960] NET: Registered protocol family 31
[ 115.163962] Bluetooth: HCI device and connection manager initialized
[ 115.163969] Bluetooth: HCI socket layer initialized
[ 115.175049] Bluetooth: L2CAP ver 2.7
[ 115.175053] Bluetooth: L2CAP socket layer initialized
[ 115.190832] Bluetooth: RFCOMM ver 1.5
[ 115.190840] Bluetooth: RFCOMM socket layer initialized
[ 115.190847] Bluetooth: RFCOMM TTY layer initialized
[ 161.562729] NET: Registered protocol family 10
[ 161.562823] Disabled Privacy Extensions on device c031eb40(lo)
[ 161.562947] IPv6 over IPv4 tunneling driver
[ 171.758620] eth0: no IPv6 routers present
[ 193.394191] usb 1-1: new low speed USB device using uhci_hcd and address 2
[ 193.655116] usbcore: registered new driver hiddev
[ 193.696150] input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.0-1
[ 193.696162] usbcore: registered new driver usbhid
[ 193.696165] drivers/usb/input/hid-core.c: v2.01:USB HID core driver

manu

Le Wed, 15 Mar 2006 21:04:15 +0100, =?ISO-8859-15?Q?Sébastien.kirche?= a
écrit :

Sinon ça pourrait venir d'un problème de timing au démarrage, genre le
montage des interfaces réseau qui se ferait avant le chargement du
module de ta carte ? Vérifie dans dmesg dans quel ordre ça se passe.

Apparemment le module (sk98lin) est chargé avant la reconnaissance de la
carte réseau :

[ 39.322935] sk98lin: Network Device Driver v8.23.1.3
[ 39.322936] (C)Copyright 1999-2005 Marvell(R).

[ 39.393830] eth0: Marvell Yukon 88E8036 Fast Ethernet Controller
[ 39.393834] PrefPort:A RlmtMode:Check Link State

... !

mais peut-être y a-t-il d'autres choses concernant le réseau que je ne
sais décripter dans dmesg (ci-dessous dans son entier)

[ 10.025070] Allocate Port Service[pcie02]
[ 10.025114] PCI: Found IRQ 11 for device 0000:00:1c.1
[ 10.025117] PCI: Sharing IRQ 11 with 0000:00:01.0
[ 10.025127] PCI: Sharing IRQ 11 with 0000:00:1d.3
[ 10.025137] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 10.025141] PCI: Sharing IRQ 11 with 0000:02:00.0
[ 10.025145] PCI: Sharing IRQ 11 with 0000:06:04.0
[ 10.025156] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 10.025205] assign_interrupt_mode Found MSI capability
[ 10.025207] Allocate Port Service[pcie00]
[ 10.025229] Allocate Port Service[pcie02]
[ 10.025254] isapnp: Scanning for PnP cards...
[ 10.378529] isapnp: No Plug & Play device found
[ 10.392395] PNP: No PS/2 controller found. Probing ports directly.
[ 10.395824] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 10.397999] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 10.398335] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 10.398601] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 10.398918] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 10.399185] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 10.399188] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
[ 10.400603] PCI: Found IRQ 5 for device 0000:00:1e.3
[ 10.400634] PCI: Sharing IRQ 5 with 0000:06:06.3
[ 10.400646] io scheduler noop registered
[ 10.400655] io scheduler anticipatory registered
[ 10.400659] io scheduler deadline registered
[ 10.400666] io scheduler cfq registered
[ 10.400936] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 10.400990] NET: Registered protocol family 2
[ 10.410339] IP: routing cache hash table of 8192 buckets, 64Kbytes
[ 10.410490] TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
[ 10.412801] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[ 10.413132] TCP: Hash tables configured (established 262144 bind 65536)
[ 10.413227] NET: Registered protocol family 8
[ 10.413230] NET: Registered protocol family 20
[ 10.413439] Freeing unused kernel memory: 168k freed
[ 10.419773] input: AT Translated Set 2 keyboard on isa0060/serio0
[ 10.425378] vga16fb: initializing
[ 10.425381] vga16fb: mapped to 0xc00a0000
[ 10.545395] Console: switching to colour frame buffer device 80x30
[ 10.545400] fb0: VGA16 VGA frame buffer device
[ 11.684969] Capability LSM initialized
[ 11.693021] NET: Registered protocol family 1
[ 11.705800] SCSI subsystem initialized
[ 11.706530] libata version 1.11 loaded.
[ 11.707262] ahci version 1.00
[ 11.707280] PCI: Found IRQ 11 for device 0000:00:1f.2
[ 11.707289] PCI: Sharing IRQ 11 with 0000:00:1d.1
[ 11.707323] ahci: probe of 0000:00:1f.2 failed with error -12
[ 11.708525] ata_piix version 1.03
[ 11.708559] PCI: Found IRQ 11 for device 0000:00:1f.2
[ 11.708568] PCI: Sharing IRQ 11 with 0000:00:1d.1
[ 11.708598] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 11.708625] ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x1100 irq 14
[ 11.862714] ata1: dev 0 cfg 49:2f00 82:746b 83:7d09 84:6023 85:7468 86:3c09 87:6023 88:203f
[ 11.862717] ata1: dev 0 ATA, max UDMA/100, 156301488 sectors: lba48
[ 11.862823] ata1: dev 0 configured for UDMA/100
[ 11.862825] scsi0 : ata_piix
[ 11.862906] Vendor: ATA Model: TOSHIBA MK8032GS Rev: AS11
[ 11.862913] Type: Direct-Access ANSI SCSI revision: 05
[ 11.863336] ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x1108 irq 15
[ 12.170330] ata2: dev 0 cfg 49:0f00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 88:0407
[ 12.170333] ata2: dev 0 ATAPI, max UDMA/33
[ 12.170335] ata2(0): applying bridge limits
[ 12.170753] ata2: dev 0 configured for UDMA/33
[ 12.170754] scsi1 : ata_piix
[ 12.172584] Vendor: MATSHITA Model: DVD-RAM UJ-841S Rev: 1.00
[ 12.172591] Type: CD-ROM ANSI SCSI revision: 05
[ 12.183301] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 12.183309] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 12.183635] ide0: I/O resource 0x1F0-0x1F7 not free.
[ 12.183638] ide0: ports already in use, skipping probe
[ 12.183640] ide1: I/O resource 0x170-0x177 not free.
[ 12.183642] ide1: ports already in use, skipping probe
[ 12.183644] Probing IDE interface ide2...
[ 12.695988] Probing IDE interface ide3...
[ 13.207693] Probing IDE interface ide4...
[ 13.719399] Probing IDE interface ide5...
[ 14.234002] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
[ 14.234010] SCSI device sda: drive cache: write back
[ 14.234063] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
[ 14.234070] SCSI device sda: drive cache: write back
[ 14.234073] /dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 >
[ 14.340502] Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
[ 14.470420] Attempting manual resume
[ 14.482745] swsusp: Suspend partition has wrong signature?
[ 14.515214] usbcore: registered new driver usbfs
[ 14.515237] usbcore: registered new driver hub
[ 14.515889] USB Universal Host Controller Interface driver v2.2
[ 14.515955] PCI: Found IRQ 11 for device 0000:00:1d.0
[ 14.515970] PCI: Sharing IRQ 11 with 0000:00:1d.7
[ 14.515998] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 14.516002] uhci_hcd 0000:00:1d.0: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1
[ 14.578018] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 14.578026] uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001200
[ 14.578115] hub 1-0:1.0: USB hub found
[ 14.578121] hub 1-0:1.0: 2 ports detected
[ 14.580919] PCI: Found IRQ 11 for device 0000:00:1d.1
[ 14.580938] PCI: Sharing IRQ 11 with 0000:00:1f.2
[ 14.580955] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 14.580959] uhci_hcd 0000:00:1d.1: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2
[ 14.642896] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 14.642901] uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001220
[ 14.642980] hub 2-0:1.0: USB hub found
[ 14.642986] hub 2-0:1.0: 2 ports detected
[ 14.645883] PCI: Found IRQ 11 for device 0000:00:1d.2
[ 14.645909] PCI: Sharing IRQ 11 with 0000:06:06.0
[ 14.645916] PCI: Sharing IRQ 11 with 0000:06:06.4
[ 14.645921] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 14.645925] uhci_hcd 0000:00:1d.2: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3
[ 14.707853] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 14.707858] uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001240
[ 14.707938] hub 3-0:1.0: USB hub found
[ 14.707944] hub 3-0:1.0: 2 ports detected
[ 14.710845] PCI: Found IRQ 11 for device 0000:00:1d.3
[ 14.710848] PCI: Sharing IRQ 11 with 0000:00:01.0
[ 14.710853] PCI: Sharing IRQ 11 with 0000:00:1c.1
[ 14.710869] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 14.710873] PCI: Sharing IRQ 11 with 0000:02:00.0
[ 14.710877] PCI: Sharing IRQ 11 with 0000:06:04.0
[ 14.710890] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 14.710894] uhci_hcd 0000:00:1d.3: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4
[ 14.772816] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[ 14.772821] uhci_hcd 0000:00:1d.3: irq 11, io base 0x00001260
[ 14.772901] hub 4-0:1.0: USB hub found
[ 14.772906] hub 4-0:1.0: 2 ports detected
[ 14.801745] PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
[ 14.801754] PCI: Found IRQ 11 for device 0000:00:1d.7
[ 14.801788] PCI: Sharing IRQ 11 with 0000:00:1d.0
[ 14.801824] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 14.801828] ehci_hcd 0000:00:1d.7: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller
[ 14.801843] ehci_hcd 0000:00:1d.7: debug port 1
[ 14.801872] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[ 14.801878] ehci_hcd 0000:00:1d.7: irq 11, io mem 0xf4000000
[ 14.805787] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 14.805795] ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
[ 14.805853] hub 5-0:1.0: USB hub found
[ 14.805859] hub 5-0:1.0: 8 ports detected
[ 17.502640] Attempting manual resume
[ 17.502819] swsusp: Suspend partition has wrong signature?
[ 17.508765] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 17.508768] EXT3-fs: write access will be enabled during recovery.
[ 17.526373] kjournald starting. Commit interval 5 seconds
[ 17.526378] EXT3-fs: recovery complete.
[ 17.526585] EXT3-fs: mounted filesystem with ordered data mode.
[ 18.531564] md: md driver 0.90.1 MAX_MD_DEVS%6, MD_SB_DISKS'
[ 21.336581] Adding 1092380k swap on /dev/sda5. Priority:-1 extents:1
[ 21.597325] EXT3 FS on sda8, internal journal
[ 27.963324] lp: driver loaded but no devices found
[ 27.989217] mice: PS/2 mouse device common for all mice
[ 28.017394] ieee1394: Initialized config rom entry `ip1394'
[ 28.020862] sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
[ 28.872470] Synaptics Touchpad, model: 1, fw: 6.2, id: 0xa5a0b1, caps: 0xa04713/0x0
[ 28.872476] synaptics: Toshiba Satellite M40 detected, limiting rate to 40pps.
[ 28.874296] input: SynPS/2 Synaptics TouchPad on isa0060/serio1
[ 29.150802] ts: Compaq touchscreen protocol output
[ 30.589523] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
[ 36.155775] kjournald starting. Commit interval 5 seconds
[ 36.155998] EXT3 FS on sda6, internal journal
[ 36.156002] EXT3-fs: mounted filesystem with ordered data mode.
[ 36.177895] kjournald starting. Commit interval 5 seconds
[ 36.178171] EXT3 FS on sda7, internal journal
[ 36.178174] EXT3-fs: mounted filesystem with ordered data mode.
[ 36.179333] kjournald starting. Commit interval 5 seconds
[ 36.179796] EXT3 FS on sda9, internal journal
[ 36.179799] EXT3-fs: mounted filesystem with ordered data mode.
[ 37.379031] Linux agpgart interface v0.101 (c) Dave Jones
[ 37.384455] agpgart: Detected an Intel 915GM Chipset.
[ 37.413116] agpgart: AGP aperture is 256M @ 0x0
[ 37.485151] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 37.488474] shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
[ 37.553342] shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
[ 37.618814] shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
[ 37.857151] hw_random: cannot enable RNG, aborting
[ 37.992751] PCI: Found IRQ 10 for device 0000:00:1e.2
[ 37.992758] PCI: Sharing IRQ 10 with 0000:00:1c.0
[ 37.992807] PCI: Setting latency timer of device 0000:00:1e.2 to 64
[ 38.802000] intel8x0_measure_ac97_clock: measured 49510 usecs
[ 38.802003] intel8x0: clocking to 48000
[ 39.322884] PCI: Found IRQ 11 for device 0000:02:00.0
[ 39.322890] PCI: Sharing IRQ 11 with 0000:00:01.0
[ 39.322895] PCI: Sharing IRQ 11 with 0000:00:1c.1
[ 39.322903] PCI: Sharing IRQ 11 with 0000:00:1d.3
[ 39.322915] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 39.322920] PCI: Sharing IRQ 11 with 0000:06:04.0
[ 39.322935] sk98lin: Network Device Driver v8.23.1.3
[ 39.322936] (C)Copyright 1999-2005 Marvell(R).
[ 39.322963] PCI: Found IRQ 11 for device 0000:02:00.0
[ 39.322966] PCI: Sharing IRQ 11 with 0000:00:01.0
[ 39.322970] PCI: Sharing IRQ 11 with 0000:00:1c.1
[ 39.322977] PCI: Sharing IRQ 11 with 0000:00:1d.3
[ 39.322988] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 39.322994] PCI: Sharing IRQ 11 with 0000:06:04.0
[ 39.323007] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 39.393830] eth0: Marvell Yukon 88E8036 Fast Ethernet Controller
[ 39.393834] PrefPort:A RlmtMode:Check Link State
[ 39.455042] ieee80211_crypt: registered algorithm 'NULL'
[ 39.463762] ieee80211: 802.11 data/management/control stack, 1.0.3
[ 39.463766] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 39.470580] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.0.6
[ 39.470583] ipw2200: Copyright(c) 2003-2004 Intel Corporation
[ 39.472965] PCI: Found IRQ 11 for device 0000:06:04.0
[ 39.472970] PCI: Sharing IRQ 11 with 0000:00:01.0
[ 39.472975] PCI: Sharing IRQ 11 with 0000:00:1c.1
[ 39.472983] PCI: Sharing IRQ 11 with 0000:00:1d.3
[ 39.472994] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 39.472998] PCI: Sharing IRQ 11 with 0000:02:00.0
[ 39.473039] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[ 40.018423] ipw2200: Radio Frequency Kill Switch is On:
[ 40.018425] Kill switch must be turned off for wireless networking to work.
[ 40.094021] Linux Kernel Card Services
[ 40.094024] options: [pci] [cardbus] [pm]
[ 40.096793] PCI: Found IRQ 11 for device 0000:06:06.0
[ 40.096804] PCI: Sharing IRQ 11 with 0000:00:1d.2
[ 40.096829] PCI: Sharing IRQ 11 with 0000:06:06.4
[ 40.096837] Yenta: CardBus bridge found at 0000:06:06.0 [1179:ff10]
[ 40.096884] Yenta: Enabling burst memory read transactions
[ 40.096889] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 40.096891] Yenta: Routing CardBus interrupts to PCI
[ 40.096897] Yenta TI: socket 0000:06:06.0, mfunc 0x01aa1b22, devctl 0x66
[ 40.317743] Yenta: ISA IRQ mask 0x02d8, PCI irq 11
[ 40.317747] Socket status: 30000006
[ 40.388658] ohci1394: $Rev: 1250 $ Ben Collins <bcollins@debian.org>
[ 40.388682] PCI: Found IRQ 11 for device 0000:06:06.2
[ 40.439133] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[b0000000-b00007ff] Max Packet=[2048]
[ 41.695450] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00080da0d128e314]
[ 41.812659] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 41.812663] Uniform CD-ROM driver Revision: 3.20
[ 41.813146] Attached scsi CD-ROM sr0 at scsi1, channel 0, id 0, lun 0
[ 41.824884] Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
[ 41.825378] Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 5
[ 42.174616] NET: Registered protocol family 17
[ 110.418325] mtrr: no more MTRRs available
[ 110.418502] mtrr: no more MTRRs available
[ 110.418610] mtrr: no more MTRRs available
[ 113.350807] apm: BIOS not found.
[ 114.159499] cs: IO port probe 0x100-0x4ff: excluding 0x300-0x307 0x310-0x31f 0x370-0x377 0x3f0-0x3f7 0x4d0-0x4d7
[ 114.162259] cs: IO port probe 0xc00-0xcf7: clean.
[ 114.162974] cs: IO port probe 0xa00-0xaff: clean.
[ 115.163952] Bluetooth: Core ver 2.7
[ 115.163960] NET: Registered protocol family 31
[ 115.163962] Bluetooth: HCI device and connection manager initialized
[ 115.163969] Bluetooth: HCI socket layer initialized
[ 115.175049] Bluetooth: L2CAP ver 2.7
[ 115.175053] Bluetooth: L2CAP socket layer initialized
[ 115.190832] Bluetooth: RFCOMM ver 1.5
[ 115.190840] Bluetooth: RFCOMM socket layer initialized
[ 115.190847] Bluetooth: RFCOMM TTY layer initialized
[ 161.562729] NET: Registered protocol family 10
[ 161.562823] Disabled Privacy Extensions on device c031eb40(lo)
[ 161.562947] IPv6 over IPv4 tunneling driver
[ 171.758620] eth0: no IPv6 routers present
[ 193.394191] usb 1-1: new low speed USB device using uhci_hcd and address 2
[ 193.655116] usbcore: registered new driver hiddev
[ 193.696150] input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.0-1
[ 193.696162] usbcore: registered new driver usbhid
[ 193.696165] drivers/usb/input/hid-core.c: v2.01:USB HID core driver

manu

Vous avez filtré cet utilisateur ! Consultez son message

Le Wed, 15 Mar 2006 21:04:15 +0100, =?ISO-8859-15?Q?Sébastien.kirche?= a
écrit :

Sinon ça pourrait venir d'un problème de timing au démarrage, genre le
montage des interfaces réseau qui se ferait avant le chargement du
module de ta carte ? Vérifie dans dmesg dans quel ordre ça se passe.

Apparemment le module (sk98lin) est chargé avant la reconnaissance de la
carte réseau :

[ 39.322935] sk98lin: Network Device Driver v8.23.1.3
[ 39.322936] (C)Copyright 1999-2005 Marvell(R).

[ 39.393830] eth0: Marvell Yukon 88E8036 Fast Ethernet Controller
[ 39.393834] PrefPort:A RlmtMode:Check Link State

... !

mais peut-être y a-t-il d'autres choses concernant le réseau que je ne
sais décripter dans dmesg (ci-dessous dans son entier)

[ 10.025070] Allocate Port Service[pcie02]
[ 10.025114] PCI: Found IRQ 11 for device 0000:00:1c.1
[ 10.025117] PCI: Sharing IRQ 11 with 0000:00:01.0
[ 10.025127] PCI: Sharing IRQ 11 with 0000:00:1d.3
[ 10.025137] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 10.025141] PCI: Sharing IRQ 11 with 0000:02:00.0
[ 10.025145] PCI: Sharing IRQ 11 with 0000:06:04.0
[ 10.025156] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 10.025205] assign_interrupt_mode Found MSI capability
[ 10.025207] Allocate Port Service[pcie00]
[ 10.025229] Allocate Port Service[pcie02]
[ 10.025254] isapnp: Scanning for PnP cards...
[ 10.378529] isapnp: No Plug & Play device found
[ 10.392395] PNP: No PS/2 controller found. Probing ports directly.
[ 10.395824] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 10.397999] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 10.398335] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 10.398601] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 10.398918] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 10.399185] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 10.399188] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
[ 10.400603] PCI: Found IRQ 5 for device 0000:00:1e.3
[ 10.400634] PCI: Sharing IRQ 5 with 0000:06:06.3
[ 10.400646] io scheduler noop registered
[ 10.400655] io scheduler anticipatory registered
[ 10.400659] io scheduler deadline registered
[ 10.400666] io scheduler cfq registered
[ 10.400936] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 10.400990] NET: Registered protocol family 2
[ 10.410339] IP: routing cache hash table of 8192 buckets, 64Kbytes
[ 10.410490] TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
[ 10.412801] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[ 10.413132] TCP: Hash tables configured (established 262144 bind 65536)
[ 10.413227] NET: Registered protocol family 8
[ 10.413230] NET: Registered protocol family 20
[ 10.413439] Freeing unused kernel memory: 168k freed
[ 10.419773] input: AT Translated Set 2 keyboard on isa0060/serio0
[ 10.425378] vga16fb: initializing
[ 10.425381] vga16fb: mapped to 0xc00a0000
[ 10.545395] Console: switching to colour frame buffer device 80x30
[ 10.545400] fb0: VGA16 VGA frame buffer device
[ 11.684969] Capability LSM initialized
[ 11.693021] NET: Registered protocol family 1
[ 11.705800] SCSI subsystem initialized
[ 11.706530] libata version 1.11 loaded.
[ 11.707262] ahci version 1.00
[ 11.707280] PCI: Found IRQ 11 for device 0000:00:1f.2
[ 11.707289] PCI: Sharing IRQ 11 with 0000:00:1d.1
[ 11.707323] ahci: probe of 0000:00:1f.2 failed with error -12
[ 11.708525] ata_piix version 1.03
[ 11.708559] PCI: Found IRQ 11 for device 0000:00:1f.2
[ 11.708568] PCI: Sharing IRQ 11 with 0000:00:1d.1
[ 11.708598] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 11.708625] ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x1100 irq 14
[ 11.862714] ata1: dev 0 cfg 49:2f00 82:746b 83:7d09 84:6023 85:7468 86:3c09 87:6023 88:203f
[ 11.862717] ata1: dev 0 ATA, max UDMA/100, 156301488 sectors: lba48
[ 11.862823] ata1: dev 0 configured for UDMA/100
[ 11.862825] scsi0 : ata_piix
[ 11.862906] Vendor: ATA Model: TOSHIBA MK8032GS Rev: AS11
[ 11.862913] Type: Direct-Access ANSI SCSI revision: 05
[ 11.863336] ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x1108 irq 15
[ 12.170330] ata2: dev 0 cfg 49:0f00 82:0000 83:0000 84:0000 85:0000 86:0000 87:0000 88:0407
[ 12.170333] ata2: dev 0 ATAPI, max UDMA/33
[ 12.170335] ata2(0): applying bridge limits
[ 12.170753] ata2: dev 0 configured for UDMA/33
[ 12.170754] scsi1 : ata_piix
[ 12.172584] Vendor: MATSHITA Model: DVD-RAM UJ-841S Rev: 1.00
[ 12.172591] Type: CD-ROM ANSI SCSI revision: 05
[ 12.183301] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 12.183309] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 12.183635] ide0: I/O resource 0x1F0-0x1F7 not free.
[ 12.183638] ide0: ports already in use, skipping probe
[ 12.183640] ide1: I/O resource 0x170-0x177 not free.
[ 12.183642] ide1: ports already in use, skipping probe
[ 12.183644] Probing IDE interface ide2...
[ 12.695988] Probing IDE interface ide3...
[ 13.207693] Probing IDE interface ide4...
[ 13.719399] Probing IDE interface ide5...
[ 14.234002] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
[ 14.234010] SCSI device sda: drive cache: write back
[ 14.234063] SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
[ 14.234070] SCSI device sda: drive cache: write back
[ 14.234073] /dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 >
[ 14.340502] Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
[ 14.470420] Attempting manual resume
[ 14.482745] swsusp: Suspend partition has wrong signature?
[ 14.515214] usbcore: registered new driver usbfs
[ 14.515237] usbcore: registered new driver hub
[ 14.515889] USB Universal Host Controller Interface driver v2.2
[ 14.515955] PCI: Found IRQ 11 for device 0000:00:1d.0
[ 14.515970] PCI: Sharing IRQ 11 with 0000:00:1d.7
[ 14.515998] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 14.516002] uhci_hcd 0000:00:1d.0: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1
[ 14.578018] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 14.578026] uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001200
[ 14.578115] hub 1-0:1.0: USB hub found
[ 14.578121] hub 1-0:1.0: 2 ports detected
[ 14.580919] PCI: Found IRQ 11 for device 0000:00:1d.1
[ 14.580938] PCI: Sharing IRQ 11 with 0000:00:1f.2
[ 14.580955] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 14.580959] uhci_hcd 0000:00:1d.1: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2
[ 14.642896] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 14.642901] uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001220
[ 14.642980] hub 2-0:1.0: USB hub found
[ 14.642986] hub 2-0:1.0: 2 ports detected
[ 14.645883] PCI: Found IRQ 11 for device 0000:00:1d.2
[ 14.645909] PCI: Sharing IRQ 11 with 0000:06:06.0
[ 14.645916] PCI: Sharing IRQ 11 with 0000:06:06.4
[ 14.645921] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 14.645925] uhci_hcd 0000:00:1d.2: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3
[ 14.707853] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 14.707858] uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001240
[ 14.707938] hub 3-0:1.0: USB hub found
[ 14.707944] hub 3-0:1.0: 2 ports detected
[ 14.710845] PCI: Found IRQ 11 for device 0000:00:1d.3
[ 14.710848] PCI: Sharing IRQ 11 with 0000:00:01.0
[ 14.710853] PCI: Sharing IRQ 11 with 0000:00:1c.1
[ 14.710869] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 14.710873] PCI: Sharing IRQ 11 with 0000:02:00.0
[ 14.710877] PCI: Sharing IRQ 11 with 0000:06:04.0
[ 14.710890] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 14.710894] uhci_hcd 0000:00:1d.3: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4
[ 14.772816] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[ 14.772821] uhci_hcd 0000:00:1d.3: irq 11, io base 0x00001260
[ 14.772901] hub 4-0:1.0: USB hub found
[ 14.772906] hub 4-0:1.0: 2 ports detected
[ 14.801745] PCI: Enabling device 0000:00:1d.7 (0000 -> 0002)
[ 14.801754] PCI: Found IRQ 11 for device 0000:00:1d.7
[ 14.801788] PCI: Sharing IRQ 11 with 0000:00:1d.0
[ 14.801824] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 14.801828] ehci_hcd 0000:00:1d.7: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller
[ 14.801843] ehci_hcd 0000:00:1d.7: debug port 1
[ 14.801872] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[ 14.801878] ehci_hcd 0000:00:1d.7: irq 11, io mem 0xf4000000
[ 14.805787] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 14.805795] ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
[ 14.805853] hub 5-0:1.0: USB hub found
[ 14.805859] hub 5-0:1.0: 8 ports detected
[ 17.502640] Attempting manual resume
[ 17.502819] swsusp: Suspend partition has wrong signature?
[ 17.508765] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 17.508768] EXT3-fs: write access will be enabled during recovery.
[ 17.526373] kjournald starting. Commit interval 5 seconds
[ 17.526378] EXT3-fs: recovery complete.
[ 17.526585] EXT3-fs: mounted filesystem with ordered data mode.
[ 18.531564] md: md driver 0.90.1 MAX_MD_DEVS%6, MD_SB_DISKS'
[ 21.336581] Adding 1092380k swap on /dev/sda5. Priority:-1 extents:1
[ 21.597325] EXT3 FS on sda8, internal journal
[ 27.963324] lp: driver loaded but no devices found
[ 27.989217] mice: PS/2 mouse device common for all mice
[ 28.017394] ieee1394: Initialized config rom entry `ip1394'
[ 28.020862] sbp2: $Rev: 1219 $ Ben Collins
[ 28.872470] Synaptics Touchpad, model: 1, fw: 6.2, id: 0xa5a0b1, caps: 0xa04713/0x0
[ 28.872476] synaptics: Toshiba Satellite M40 detected, limiting rate to 40pps.
[ 28.874296] input: SynPS/2 Synaptics TouchPad on isa0060/serio1
[ 29.150802] ts: Compaq touchscreen protocol output
[ 30.589523] device-mapper: 4.4.0-ioctl (2005-01-12) initialised:
[ 36.155775] kjournald starting. Commit interval 5 seconds
[ 36.155998] EXT3 FS on sda6, internal journal
[ 36.156002] EXT3-fs: mounted filesystem with ordered data mode.
[ 36.177895] kjournald starting. Commit interval 5 seconds
[ 36.178171] EXT3 FS on sda7, internal journal
[ 36.178174] EXT3-fs: mounted filesystem with ordered data mode.
[ 36.179333] kjournald starting. Commit interval 5 seconds
[ 36.179796] EXT3 FS on sda9, internal journal
[ 36.179799] EXT3-fs: mounted filesystem with ordered data mode.
[ 37.379031] Linux agpgart interface v0.101 (c) Dave Jones
[ 37.384455] agpgart: Detected an Intel 915GM Chipset.
[ 37.413116] agpgart: AGP aperture is 256M @ 0x0
[ 37.485151] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 37.488474] shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
[ 37.553342] shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
[ 37.618814] shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x1001
[ 37.857151] hw_random: cannot enable RNG, aborting
[ 37.992751] PCI: Found IRQ 10 for device 0000:00:1e.2
[ 37.992758] PCI: Sharing IRQ 10 with 0000:00:1c.0
[ 37.992807] PCI: Setting latency timer of device 0000:00:1e.2 to 64
[ 38.802000] intel8x0_measure_ac97_clock: measured 49510 usecs
[ 38.802003] intel8x0: clocking to 48000
[ 39.322884] PCI: Found IRQ 11 for device 0000:02:00.0
[ 39.322890] PCI: Sharing IRQ 11 with 0000:00:01.0
[ 39.322895] PCI: Sharing IRQ 11 with 0000:00:1c.1
[ 39.322903] PCI: Sharing IRQ 11 with 0000:00:1d.3
[ 39.322915] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 39.322920] PCI: Sharing IRQ 11 with 0000:06:04.0
[ 39.322935] sk98lin: Network Device Driver v8.23.1.3
[ 39.322936] (C)Copyright 1999-2005 Marvell(R).
[ 39.322963] PCI: Found IRQ 11 for device 0000:02:00.0
[ 39.322966] PCI: Sharing IRQ 11 with 0000:00:01.0
[ 39.322970] PCI: Sharing IRQ 11 with 0000:00:1c.1
[ 39.322977] PCI: Sharing IRQ 11 with 0000:00:1d.3
[ 39.322988] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 39.322994] PCI: Sharing IRQ 11 with 0000:06:04.0
[ 39.323007] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 39.393830] eth0: Marvell Yukon 88E8036 Fast Ethernet Controller
[ 39.393834] PrefPort:A RlmtMode:Check Link State
[ 39.455042] ieee80211_crypt: registered algorithm 'NULL'
[ 39.463762] ieee80211: 802.11 data/management/control stack, 1.0.3
[ 39.463766] ieee80211: Copyright (C) 2004-2005 Intel Corporation
[ 39.470580] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.0.6
[ 39.470583] ipw2200: Copyright(c) 2003-2004 Intel Corporation
[ 39.472965] PCI: Found IRQ 11 for device 0000:06:04.0
[ 39.472970] PCI: Sharing IRQ 11 with 0000:00:01.0
[ 39.472975] PCI: Sharing IRQ 11 with 0000:00:1c.1
[ 39.472983] PCI: Sharing IRQ 11 with 0000:00:1d.3
[ 39.472994] PCI: Sharing IRQ 11 with 0000:01:00.0
[ 39.472998] PCI: Sharing IRQ 11 with 0000:02:00.0
[ 39.473039] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
[ 40.018423] ipw2200: Radio Frequency Kill Switch is On:
[ 40.018425] Kill switch must be turned off for wireless networking to work.
[ 40.094021] Linux Kernel Card Services
[ 40.094024] options: [pci] [cardbus] [pm]
[ 40.096793] PCI: Found IRQ 11 for device 0000:06:06.0
[ 40.096804] PCI: Sharing IRQ 11 with 0000:00:1d.2
[ 40.096829] PCI: Sharing IRQ 11 with 0000:06:06.4
[ 40.096837] Yenta: CardBus bridge found at 0000:06:06.0 [1179:ff10]
[ 40.096884] Yenta: Enabling burst memory read transactions
[ 40.096889] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 40.096891] Yenta: Routing CardBus interrupts to PCI
[ 40.096897] Yenta TI: socket 0000:06:06.0, mfunc 0x01aa1b22, devctl 0x66
[ 40.317743] Yenta: ISA IRQ mask 0x02d8, PCI irq 11
[ 40.317747] Socket status: 30000006
[ 40.388658] ohci1394: $Rev: 1250 $ Ben Collins
[ 40.388682] PCI: Found IRQ 11 for device 0000:06:06.2
[ 40.439133] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[b0000000-b00007ff] Max Packet=[2048]
[ 41.695450] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00080da0d128e314]
[ 41.812659] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 41.812663] Uniform CD-ROM driver Revision: 3.20
[ 41.813146] Attached scsi CD-ROM sr0 at scsi1, channel 0, id 0, lun 0
[ 41.824884] Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
[ 41.825378] Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 5
[ 42.174616] NET: Registered protocol family 17
[ 110.418325] mtrr: no more MTRRs available
[ 110.418502] mtrr: no more MTRRs available
[ 110.418610] mtrr: no more MTRRs available
[ 113.350807] apm: BIOS not found.
[ 114.159499] cs: IO port probe 0x100-0x4ff: excluding 0x300-0x307 0x310-0x31f 0x370-0x377 0x3f0-0x3f7 0x4d0-0x4d7
[ 114.162259] cs: IO port probe 0xc00-0xcf7: clean.
[ 114.162974] cs: IO port probe 0xa00-0xaff: clean.
[ 115.163952] Bluetooth: Core ver 2.7
[ 115.163960] NET: Registered protocol family 31
[ 115.163962] Bluetooth: HCI device and connection manager initialized
[ 115.163969] Bluetooth: HCI socket layer initialized
[ 115.175049] Bluetooth: L2CAP ver 2.7
[ 115.175053] Bluetooth: L2CAP socket layer initialized
[ 115.190832] Bluetooth: RFCOMM ver 1.5
[ 115.190840] Bluetooth: RFCOMM socket layer initialized
[ 115.190847] Bluetooth: RFCOMM TTY layer initialized
[ 161.562729] NET: Registered protocol family 10
[ 161.562823] Disabled Privacy Extensions on device c031eb40(lo)
[ 161.562947] IPv6 over IPv4 tunneling driver
[ 171.758620] eth0: no IPv6 routers present
[ 193.394191] usb 1-1: new low speed USB device using uhci_hcd and address 2
[ 193.655116] usbcore: registered new driver hiddev
[ 193.696150] input: USB HID v1.10 Mouse [Logitech Optical USB Mouse] on usb-0000:00:1d.0-1
[ 193.696162] usbcore: registered new driver usbhid
[ 193.696165] drivers/usb/input/hid-core.c: v2.01:USB HID core driver

manu

Pb carte réseau (portable)

5 réponses

Veuillez sélectionner un problème