[Ubuntu] pb de montage d'un disque dur usb externe (sda: assuming drive cache: write through)

Le
Bifidus
Bonjour.

Ce disque dur externe (Lacie, USB 2.0) fonctionnait trs bien avec la
version 4.10 d'Ubuntu.
Depuis la 5.04, il n'est plus utilisable.

Symptmes :
- ds l'installation (pendant l'installation), le message "sda:
assuming drive cache: write through" envahit la console environ une
fois par seconde. Il apparait galement ds que le disque externe est
allum.
- disque dur externe non reconnu, ne monte pas
- programme systme>administration>gestionnaire de priphriques se
plante ds le lancement
- l'occupation cpu passe 100% au mme rythme que les messages sur
la console, ce qui rend le systme trs peu ractif
- tous les symptmes disparaissent si j'teins le dd (mais comme
toutes les donnes sont dessus)

Quelques recherches sur google me laissent penser qu'il s'agit d'un
problme de pilote, mais je n'en ai pas compris plus.

La lecture d'un post m'a fait rajouter uhci-hcd la fin de
/etc/modules, sans grand succs : les symptmes disparaissent, mais
le disque n'est toujours pas mont ni reconnu (j'ai supprim ohci-hcd
par la commande rmmod, sinon les symptmes persistent). Mais en
touchant aux modules, je joue clairement l'apprenti sorcier : cela
dpasse de loin mes connaissances.

C'est peu prs tout, n'hsitez pas me poser des questions.

dmesg :

annot allocate resource for EISA slot 8
EISA: Detected 0 cards.
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 16384)
NET: Registered protocol family 8
NET: Registered protocol family 20
Restarting tasks<6> Strange, kswapd0 not stopped
Strange, kseriod not stopped
done
ACPI wakeup devices:
SLPB LAN MOD
ACPI: (supports S0 S3 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4300KiB [1 disk] into ram disk done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 224k freed
ACPI: Processor [CPU0] (supports 8 throttling states)
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
SIS5513: IDE controller at PCI slot 0000:00:00.1
ACPI: PCI interrupt 0000:00:00.1[A]: no GSI
SIS5513: chipset revision 208
SIS5513: not 100% native mode: will probe irqs later
SIS5513: SiS630 ATA 100 (1st gen) controller
ide0: BM-DMA at 0x1880-0x1887, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x1888-0x188f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0
hda: FUJITSU MHN2100AT, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 128KiB
hda: 19640880 sectors (10056 MB) w/2048KiB Cache, CHS=19485/16/63,
UDMA(100)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 >
Probing IDE interface ide1
hdc: Pioneer DVD-ROM ATAPIModel DVD-K11 1.05, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2
Probing IDE interface ide3
Probing IDE interface ide4
Probing IDE interface ide5
Stopping tasks: ==|
Freeing memory done (458 pages freed)
Restarting tasks done
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
Adding 337324k swap on /dev/hda5. Priority:-1 extents:1
EXT3 FS on hda1, internal journal
hdc: ATAPI DVD-ROM drive, 512kB Cache
Uniform CD-ROM driver Revision: 3.20
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
mice: PS/2 mouse device common for all mice
Synaptics Touchpad, model: 1
Firmware: 4.1
180 degree mounted touchpad
Sensor: 8
new absolute packet format
ts: Compaq touchscreen protocol output
input: SynPS/2 Synaptics TouchPad on isa0060/serio1
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
Capability LSM initialized
device-mapper: 4.3.0-ioctl (2004-09-30) initialised:
dm-devel@redhat.com
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
cdrom: open failed.
Real Time Clock Driver v1.12
input: PC Speaker
irda_init()
NET: Registered protocol family 23
inserting floppy driver for 2.6.10-5-386
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected SiS 630 chipset
agpgart: Maximum main memory to use for agp memory: 86M
agpgart: AGP aperture is 64M @ 0xe8000000
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver
(PCI)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI interrupt 0000:00:01.2[D] -> GSI 5 (level, low) -> IRQ 5
ohci_hcd 0000:00:01.2: Silicon Integrated Systems [SiS] USB 1.0
Controller
ohci_hcd 0000:00:01.2: irq 5, pci mem 0xec000000
ohci_hcd 0000:00:01.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
usb 1-2: new full speed USB device using ohci_hcd and address 2
usb 1-2: device descriptor read/64, error -110
usb 1-2: device descriptor read/64, error -110
usb 1-2: new full speed USB device using ohci_hcd and address 3
usb 1-2: device descriptor read/64, error -110
usb 1-2: device descriptor read/64, error -110
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
ACPI: PCI interrupt 0000:00:01.4[B] -> GSI 5 (level, low) -> IRQ 5
cpci_hotplug: CompactPCI Hot Plug Core version: 0.2
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Evaluate _OSC Set fails. Status = 0x0005
pciehp: add_host_bridge: status 5
pciehp: Fails to gain control of native hot-plug
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 9 (level, low) -> IRQ 9
Yenta: CardBus bridge found at 0000:00:08.0 [1631:8000]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:08.0, mfunc 0x01001000, devctl 0x66
Yenta: ISA IRQ mask 0x0418, PCI irq 9
Socket status: 30000006
ACPI: PCI interrupt 0000:00:08.1[A] -> GSI 9 (level, low) -> IRQ 9
Yenta: CardBus bridge found at 0000:00:08.1 [1631:8000]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:08.1, mfunc 0x01001000, devctl 0x66
Yenta: ISA IRQ mask 0x0418, PCI irq 9
Socket status: 30000020
Linux Tulip driver version 1.1.13 (May 11, 2002)
PCI: Enabling device 0000:06:00.0 (0000 -> 0003)
ACPI: PCI interrupt 0000:06:00.0[A] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:06:00.0 to 64
tulip0: MII transceiver #1 config 3100 status 7849 advertising 05e1.
eth0: ADMtek Comet rev 17 at 00014800, 00:0F:B5:41:33:8E, IRQ 9.
NET: Registered protocol family 17
0000:06:00.0: tulip_stop_rxtx() failed
eth0: Setting full-duplex based on MII#1 link partner capability of
45e1.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02f0500(lo)
IPv6 over IPv4 tunneling driver
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Lid Switch [LID]
ibm_acpi: ec object not found
eth0: no IPv6 routers present
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
[drm] Initialized drm 1.0.0 20040925
[drm] Initialized sis 1.1.0 20030826 on minor 0: Silicon Integrated
Systems [SiS ] 630/730 PCI/AGP VGA Display Adapter
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
cs: IO port probe 0x0100-0x04ff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
usb 1-2: new full speed USB device using ohci_hcd and address 4
SCSI subsystem initialized
Initializing USB Mass Storage driver
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
Vendor: LaCie Model: Big Disk G298 Rev:
Type: Direct-Access ANSI SCSI revision: 04
usb-storage: device scan complete
usb 1-2: USB disconnect, address 4
scsi: Device offlined - not ready after error recovery: host 0 channel
0 id 0 lu n 0
sd 0:0:0:0: Illegal state transition cancel->offline
Badness in scsi_device_set_state at drivers/scsi/scsi_lib.c:1718
[<c839c8c7>] scsi_device_set_state+0xcc/0xd7 [scsi_mod]
[<c839a93b>] scsi_eh_offline_sdevs+0x47/0x60 [scsi_mod]
[<c839ae7d>] scsi_unjam_host+0x18d/0x1a2 [scsi_mod]
[<c839af6d>] scsi_error_handler+0xdb/0x11f [scsi_mod]
[<c839ae92>] scsi_error_handler+0x0/0x11f [scsi_mod]
[<c01011f9>] kernel_thread_helper+0x5/0xb
sda : READ CAPACITY failed.
sda : status=0, message=00, host=1, driver=00
sda : sense not available.
sda: assuming drive cache: write through
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
usb 1-2: new full speed USB device using ohci_hcd and address 5
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
Vendor: LaCie Model: Big Disk G298 Rev:
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sda: 625163615 512-byte hdwr sectors (320084 MB)
sda: assuming drive cache: write through
SCSI device sda: 625163615 512-byte hdwr sectors (320084 MB)
sda: assuming drive cache: write through
/dev/scsi/host1/bus0/target0/lun0: p1
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
usb-storage: device scan complete
usb 1-2: USB disconnect, address 5
usb 1-2: new full speed USB device using ohci_hcd and address 6
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 6
usb-storage: waiting for device to settle before scanning
Vendor: LaCie Model: Big Disk G298 Rev:
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sda: 625163615 512-byte hdwr sectors (320084 MB)
sda: assuming drive cache: write through
SCSI device sda: 625163615 512-byte hdwr sectors (320084 MB)
sda: assuming drive cache: write through
/dev/scsi/host2/bus0/target0/lun0: p1
Attached scsi disk sda at scsi2, channel 0, id 0, lun 0
usb 1-2: USB disconnect, address 6
scsi: Device offlined - not ready after error recovery: host 2 channel
0 id 0 lu n 0
usb-storage: device scan complete
usb 1-2: new full speed USB device using ohci_hcd and address 7
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 7
usb-storage: waiting for device to settle before scanning
Vendor: LaCie Model: Big Disk G298 Rev:
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sda: 625163615 512-byte hdwr sectors (320084 MB)
sda: assuming drive cache: write through
SCSI device sda: 625163615 512-byte hdwr sectors (320084 MB)
sda: assuming drive cache: write through
/dev/scsi/host3/bus0/target0/lun0: p1
Attached scsi disk sda at scsi3, channel 0, id 0, lun 0
usb-storage: device scan complete
usb 1-2: USB disconnect, address 7
usb 1-2: new full speed USB device using ohci_hcd and address 8
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 8
usb-storage: waiting for device to settle before scanning
Vendor: LaCie Model: Big Disk G298 Rev:
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sda: 625163615 512-byte hdwr sectors (320084 MB)
sda: assuming drive cache: write through
SCSI device sda: 625163615 512-byte hdwr sectors (320084 MB)
sda: assuming drive cache: write through
/dev/scsi/host4/bus0/target0/lun0: p1
Attached scsi disk sda at scsi4, channel 0, id 0, lun 0
usb 1-2: USB disconnect, address 8
usb-storage: device scan complete
usb 1-2: new full speed USB device using ohci_hcd and address 9
scsi5 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 9
usb-storage: waiting for device to settle before scanning
Vendor: LaCie Model: Big Disk G298 Rev:
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sda: 625163615 512-byte hdwr sectors (320084 MB)
sda: assuming drive cache: write through
SCSI device sda: 625163615 512-byte hdwr sectors (320084 MB)
sda: assuming drive cache: write through
/dev/scsi/host5/bus0/target0/lun0: p1
Attached scsi disk sda at scsi5, channel 0, id 0, lun 0
usb-storage: device scan complete
usb 1-2: USB disconnect, address 9
usb 1-2: new full speed USB device using ohci_hcd and address 10
scsi6 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 10
usb-storage: waiting for device to settle before scanning
Vendor: LaCie Model: Big Disk G298 Rev:
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sda: 625163615 512-byte hdwr sectors (320084 MB)
sda: assuming drive cache: write through
SCSI device sda: 625163615 512-byte hdwr sectors (320084 MB)
sda: assuming drive cache: write through
/dev/scsi/host6/bus0/target0/lun0: p1
Attached scsi disk sda at scsi6, channel 0, id 0, lun 0
usb-storage: device scan complete
usb 1-2: USB disconnect, address 10
usb 1-2: new full speed USB device using ohci_hcd and address 11
scsi7 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 11
usb-storage: waiting for device to settle before scanning
Vendor: LaCie Model: Big Disk G298 Rev:
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sda: 625163615 512-byte hdwr sectors (320084 MB)
sda: assuming drive cache: write through
SCSI device sda: 625163615 512-byte hdwr sectors (320084 MB)
sda: assuming drive cache: write through
/dev/scsi/host7/bus0/target0/lun0: p1
Attached scsi disk sda at scsi7, channel 0, id 0, lun 0
usb 1-2: USB disconnect, address 11
scsi: Device offlined - not ready after error recovery: host 7 channel
0 id 0 lu n 0
usb-storage: device scan complete
usb 1-2: new full speed USB device using ohci_hcd and address 12
scsi8 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 12
usb-storage: waiting for device to settle before scanning
Vendor: LaCie Model: Big Disk G298 Rev:
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sda: 625163615 512-byte hdwr sectors (320084 MB)
sda: assuming drive cache: write through
SCSI device sda: 625163615 512-byte hdwr sectors (320084 MB)
sda: assuming drive cache: write through
/dev/scsi/host8/bus0/target0/lun0: p1
Attached scsi disk sda at scsi8, channel 0, id 0, lun 0
usb-storage: device scan complete
usb 1-2: USB disconnect, address 12
usb 1-2: new full speed USB device using ohci_hcd and address 13
scsi9 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 13
usb-storage: waiting for device to settle before scanning
Vendor: LaCie Model: Big Disk G298 Rev:
Type: Direct-Access ANSI SCSI revision: 04
SCSI device sda: 625163615 512-byte hdwr sectors (320084 MB)
sda: assuming drive cache: write through
SCSI device sda: 625163615 512-byte hdwr sectors (320084 MB)
sda: assuming drive cache: write through
/dev/scsi/host9/bus0/target0/lun0: p1
Attached scsi disk sda at scsi9, channel 0, id 0, lun 0
usb 1-2: USB disconnect, address 13
scsi: Device offlined - not ready after error recovery: host 9 channel
0 id 0 lu n 0
usb-storage: device scan complete
usb 1-2: new full speed USB device using ohci_hcd and address 14
scsi10 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 14
usb-storage: waiting for device to settle before scanning
ohci_hcd 0000:00:01.2: remove, state 1
usb usb1: USB disconnect, address 1
usb 1-2: USB disconnect, address 14
ohci_hcd 0000:00:01.2: USB bus 1 deregistered

lsmod :

Module Size Used by
sd_mod 16784 0
usb_storage 64064 0
scsi_mod 119936 2 sd_mod,usb_storage
proc_intf 4100 0
freq_table 4100 0
cpufreq_userspace 4572 0
cpufreq_ondemand 6172 0
cpufreq_powersave 1920 0
pcmcia 21380 4
sis 10944 1
drm 59412 2 sis
video 16260 0
sony_acpi 6280 0
pcc_acpi 11264 0
button 6800 0
battery 10244 0
container 4608 0
ac 4996 0
ipv6 229504 9
af_packet 20744 2
tulip 46112 0
yenta_socket 19584 1
pcmcia_core 53568 2 pcmcia,yenta_socket
shpchp 86116 0
pci_hotplug 30512 1 shpchp
snd_trident 41380 2
snd_ac97_codec 64608 1 snd_trident
snd_pcm_oss 47652 1
snd_mixer_oss 16768 2 snd_pcm_oss
snd_pcm 84872 3 snd_trident,snd_ac97_codec,snd_pcm_oss
snd_timer 23300 1 snd_pcm
snd_page_alloc 9604 2 snd_trident,snd_pcm
gameport 4608 1 snd_trident
snd_util_mem 4608 1 snd_trident
snd_mpu401_uart 7168 1 snd_trident
snd_rawmidi 22944 1 snd_mpu401_uart
snd_seq_device 8332 2 snd_trident,snd_rawmidi
snd 50276 9
snd_trident,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer,snd_=
mpu401_uart,snd_rawmidi,snd_seq_device
soundcore 9824 3 snd
i2c_sis630 7436 0
i2c_core 21264 1 i2c_sis630
sis_agp 8068 1
agpgart 31784 2 drm,sis_agp
floppy 54864 0
irtty_sir 7936 0
sir_dev 18092 1 irtty_sir
irda 168000 2 irtty_sir,sir_dev
crc_ccitt 2176 1 irda
pcspkr 3816 0
rtc 12216 0
md 43856 0
dm_mod 53116 1
capability 5000 0
commoncap 7808 1 capability
uhci_hcd 30224 0
usbcore 107384 3 usb_storage,uhci_hcd
joydev 9408 0
tsdev 7488 0
evdev 9088 1
psmouse 19336 0
mousedev 11160 1
parport_pc 34372 1
lp 10792 0
parport 33480 2 parport_pc,lp
ide_cd 38532 0
cdrom 36508 1 ide_cd
ext3 120968 1
jbd 54168 1 ext3
ide_generic 1664 0
sis5513 15112 1
ide_disk 18176 3
ide_core 118988 5
usb_storage,ide_cd,ide_generic,sis5513,ide_disk
unix 26164 820
thermal 13576 0
processor 22708 1 thermal
fan 4612 0
fbcon 34048 0
font 8448 1 fbcon
bitblit 5120 1 fbcon
vesafb 6948 0
cfbcopyarea 3968 1 vesafb
cfbimgblt 3072 1 vesafb
cfbfillrect 3584 1 vesafb

lspci :

0000:00:00.0 Host bridge: Silicon Integrated Systems [SiS] 630 Host
(rev 31)
0000:00:00.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE]
(rev d0)
0000:00:01.0 ISA bridge: Silicon Integrated Systems [SiS]
SiS85C503/5513 (LPC Bridge)
0000:00:01.2 USB Controller: Silicon Integrated Systems [SiS] USB 1.0
Controller (rev 07)
0000:00:01.4 Multimedia audio controller: Silicon Integrated Systems
[SiS] SiS PCI Audio Accelerator (rev 02)
0000:00:01.6 Modem: Silicon Integrated Systems [SiS] AC'97 Modem
Controller (rev a0)
0000:00:02.0 PCI bridge: Silicon Integrated Systems [SiS] Virtual
PCI-to-PCI bridge (AGP)
0000:00:08.0 CardBus bridge: Texas Instruments PCI1225 (rev 01)
0000:00:08.1 CardBus bridge: Texas Instruments PCI1225 (rev 01)
0000:01:00.0 VGA compatible controller: Silicon Integrated Systems
[SiS] 630/730 PCI/AGP VGA Display Adapter (rev 31)
0000:06:00.0 Ethernet controller: Linksys 21x4x DEC-Tulip compatible
10/100 Ethernet (rev 11)

lsusb : rien du tout

Merci d'avance pour votre aide,

--
Damien

  • Partager ce contenu :
Vos réponses
Trier par : date / pertinence
Nicolas S.
Le #1406116
Bonjour.


Bonjour,


Ce disque dur externe (Lacie, USB 2.0) fonctionnait très bien avec la
version 4.10 d'Ubuntu.
Depuis la 5.04, il n'est plus utilisable.


C'est probablement dû à la version du kernel. Revenez à la v4.10
d'Ubuntu ou essayez vous à la 5.10.
L'USB fait l'objet d'une évolution active (en ce moment avec 2.6.12-rc5).

Merci d'avance pour votre aide,


Cordialement,
Nicolas S.


--
Il est toujours sympa de laisser un petit message pour expliquer
comment on a réussi à se sortir d'une difficulté.
Cela aide les autres qui pourraient avoir rencontré les mêmes problèmes,
mais aussi les contributeurs. ;-)

E-mail: enlever "-heh" pour m'écrire.

Bifidus
Le #1398569
Bonjour.

(désolé pour l'absence de citation, il semblerait que l'interface
groups.google.com ait changé)

La 5.10 ?
Mais... elle n'est pas encore sortie, si j'ai compris la nomenclature
Ubuntu : dernier chiffre_l_année_.mois_de_l_année.
Repasser en 4.10... oui, c'est surement ce que je devrai faire, à
moins de trifouiller moi-même le système, ce que je ne souhaite pas
(pour différentes raisons complémentaires, dont le fait qu'il ne
s'agisse pas de ma machine, et que je ne peux m'en occuper
qu'épisodiquement, et surtout le moins souvent possible ;-).

Un peu dommage, ceci dit, qu'un bug aussi énorme soit sorti dans une
version stable.

Merci pour l'info,

--
Damien
Poster une réponse
Anonyme